Subscribe to Our Youtube Channel
Related Manuals for IBASE Technology ET880 Series
Summary of Contents for IBASE Technology ET880 Series
- Page 1 ET880 Series COM Express (Type 6 & R3.0) Module with Intel® Atom® x6000 Series SoC User’s Manual Version 1.0 (April 2023)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
- Page 3 0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) ET880 Series User’s Manual...
- Page 4 Danger of explosion if the internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. ET880 Series User’s Manual...
- Page 5 Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. ET880 Series User’s Manual...
-
Page 6: Table Of Contents
Chapter 4 BIOS Setup ............29 Introduction ................... 30 BIOS Setup ................... 30 Main Settings................. 31 Advanced Settings ................. 31 Chipset Settings ................43 Security Settings ................45 Boot Settings ................. 47 Save & Exit Settings............... 48 ET880 Series User’s Manual... - Page 7 Appendix..................49 I/O Port Address Map..............50 Interrupt Request Lines (IRQ) ............52 Watchdog Timer Configuration ............53 ET880 Series User’s Manual...
- Page 8 This page is intentionally left blank. ET880 Series User’s Manual viii...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Block Diagram • Product View • Board Dimensions... -
Page 10: Introduction
1x I226IT PCI-E 2.5G LAN • 2x USB 3.1, 4x USB 2.0, 2x SATA III, 2x UART (Tx/Rx only) • Supports 3x independent displays, DisplayPort /DVI-D / LVDS or eDP via carrier board (IP419) • Supports wide-range operating temperature ET880 Series User’s Manual... -
Page 11: Packing List
• Intel® Atom® QC x6425E (1.8Ghz/3.0GHz) • Intel® Atom® DC x6211E (1.2Ghz/3.0GHz) Integrated in Intel® SoC • Onboard DDR4 8GB & 1x DDR4 SO-DIMM Memory Type • Max. 24GB, IBECC compatible BIOS 256 levels Watchdog Timer ET880 Series User’s Manual... - Page 12 95mm x 95mm (3.74“ x 3.74“) Dimensions (L X W) -40°C~+85°C ( -40°F~+185°F); Operating excluding SO-DIMM memory module Temperature -40°C~90°C (-40°F~+194°F) Storage Temperature 90% (non-condensing @60°C) Relative Humidity All specifications are subject to change without prior notice. ET880 Series User’s Manual...
-
Page 13: Block Diagram
General Information Block Diagram ET880 Series User’s Manual... -
Page 14: Product View
Product View Top View Bottom View ＊The photos above are for reference only. Some minor components may differ. ET880 Series User’s Manual... -
Page 15: Dimensions
General Information Dimensions Unit: mm ET880 Series User’s Manual... - Page 16 This page is intentionally left blank. ET880 Series User’s Manual...
-
Page 17: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the ET880 in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. The topics covered are: •... -
Page 18: Installations
Gently push the module in an upright position until the clips of the slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the clips outwards with both hands, and the module will pop-up. ET880 Series User’s Manual... -
Page 19: Switch, Jumper And Connector Location
Hardware Configuration Switch, Jumper and Connector Location ET880 Series User’s Manual... -
Page 20: Switch And Connector Quick Reference
AT / ATX Mode Switch Connector to Carrier Board SOM1, SOM2 DDR4 SO-DIMM Slot 2.3.1 AT / ATX Mode Switch (SW1) Function Pin closed Illustration ATX Mode (default) OFF (Pin 1) AT Mode ON (Pin 2) ET880 Series User’s Manual... -
Page 21: Com Express Module Type 6 Connector (Som1, Som2)
PCIE_RX7-(NC) PCIE_TX7-(NC) SUS_S5# PWR_OK DDI1_HPD RSVD(NC) SATA2_RX+(NC) SATA3_RX+(NC) C25 DDI1_PAIR4+(NC) D25 RSVD(NC) SATA2_RX-(NC) SATA3_RX-(NC) DDI1_PAIR4-(NC) D26 DDI1_PAIR0+ BATLOW# RSVD(NC) DDI1_PAIR0- SATA_ACT# HDA_SDIN2(NC) C28 RSVD(NC) RSVD(NC) HDA_SYNC HDA_SDIN1(NC) C29 DDI1_PAIR5+(NC) D29 DDI1_PAIR1+ HDA_RST# HDA_SDIN0 DDI1_PAIR5-(NC) D30 DDI1_PAIR1- ET880 Series User’s Manual... - Page 22 RAPID_SHUTDOW N(NC) PCIE_TX0+ PCIE_RX0+ PEG_RX5+(NC) PEG_TX5+(NC) PCIE_TX0- PCIE_RX0- PEG_RX5-(NC) PEG_TX5-(NC) GND (FIXED) GND (FIXED) GND (FIXED) GND (FIXED) LVDS_A0+ LVDS_B0+ PEG_RX6+(NC) PEG_TX6+(NC) LVDS_A0- LVDS_B0- PEG_RX6-(NC) PEG_TX6-(NC) LVDS_A1+ LVDS_B1+ LVDS_A1- LVDS_B1- PEG_RX7+(NC) PEG_TX7+(NC) LVDS_A2+ LVDS_B2+ PEG_RX7-(NC) PEG_TX7-(NC) ET880 Series User’s Manual...
- Page 23 A107 VCC_12V B107 VCC_12V C107 VCC_12V D107 VCC_12V A108 VCC_12V B108 VCC_12V C108 VCC_12V D108 VCC_12V A109 VCC_12V B109 VCC_12V C109 VCC_12V D109 VCC_12V A110 GND (FIXED) B110 GND (FIXED) C110 GND (FIXED) D110 GND (FIXED) ET880 Series User’s Manual...
- Page 24 This page is intentionally left blank. ET880 Series User’s Manual...
-
Page 25: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • Graphics Driver • HD Audio Driver • ® Intel ME Drivers • LAN Driver... -
Page 26: Introduction
INF files for Plug & Play function for Intel chipset components. Follow the instructions below to complete the installation. Run the drivers disk. Click Intel on the left pane and then Intel(R) Elkhartlake Chipset Drivers on the right pane. ET880 Series User’s Manual... - Page 27 Chipset Device Software appears, click Next. Accept the software license agreement and click Yes. On the Readme File Information screen, click Install. When the driver has been completely installed, restart the computer for changes to take effect. ET880 Series User’s Manual...
-
Page 28: Graphics Driver Installation
Graphics Driver Installation Run the drivers disk. Click Intel on the left pane and then Intel(R) Elkhartlake Chipset Drivers on the right pane. Click Intel(R) Elkhartlake Graphics Driver. ET880 Series User’s Manual... - Page 29 When the intel Graphics Driver Installer screen appears, click Begin Installation. Accept the Intel Software License Agreement. Click I agree. The installer shows the components to be installed. Click Start. When the screen shows the message “Installation complete!”, click Finish. ET880 Series User’s Manual...
-
Page 30: Hd Audio Driver Installation
HD Audio Driver Installation Run the drivers disk. Click Intel on the left pane and then Intel(R) Elkhartlake Chipset Drivers on the right pane. Click Realtek High Definition Audio Driver. ET880 Series User’s Manual... - Page 31 Driver Installation On the Welcome screen of the InstallShield Wizard, click Next. On the next screen, click Next. When InstallShield Wizard has finished the installation, click Finish. ET880 Series User’s Manual...
-
Page 32: Intel ® Me Drivers
® Intel ME Drivers Run the drivers disk. Click Intel on the left pane and then Intel(R) Elkhartlake Chipset Drivers on the right pane. Click Intel(R) ME Drivers to install the Intel Management Engine Components. ET880 Series User’s Manual... - Page 33 When the Welcome screen appears, click Next. Accept the license agreement and click Next. Click Next to install to the default folder, or click Change to choose another destination folder. When the components have been installed, click Finish. ET880 Series User’s Manual...
-
Page 34: Lan Driver Installation
LAN Driver Installation Run the drivers disk. Click LAN Card on the left pane and then Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x / I22x Gigabit Network Drivers.. ET880 Series User’s Manual... - Page 35 On the Welcome screen to the install wizard for Intel(R) Network connections, click Next. On the Setup Options screen, click Next. On the next screen, click Install to begin installation. When Install wizard has completed the installation, click Finish. ET880 Series User’s Manual...
- Page 36 This page is intentionally left blank. ET880 Series User’s Manual...
-
Page 37: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 38: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. ET880 Series User’s Manual... -
Page 39: Main Settings
Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. Note: The item LVDS (eDP/DP) Configuration is only available for ET880-6425ELV & ET880-6211ELV. ET880 Series User’s Manual... - Page 40 BIOS Setting Description M.2 Select Selects SATA or PCIe interface for M.2. 4.4.2 CPU Configuration BIOS Setting Description Intel (VMX) Virtualization When enabled, a VMX can utilize the Technology additional hardware capabilities provided by Vanderpool Technology. ET880 Series User’s Manual...
- Page 41 BIOS Setup 4.4.3 PCH-FW Configuration PCH-FW Configuration: Configure Management Engine Technology Parameters. BIOS Setting Description When disabled, ME will be put into ME Temporarily ME State Disabled Mode. ET880 Series User’s Manual...
- Page 42 TPM 2.0 will restrict support to TPM 2.0 devices only. Device Select • Auto will support both with the default being set to TPM 2.0 deices if not found, and TPM 1.2 device will be enumerated. ET880 Series User’s Manual...
- Page 43 Enable Hibernation (OS/S4 Sleep State). This option may be not effective with some OS. Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the ACPI Sleep State Suspend button is pressed. ET880 Series User’s Manual...
- Page 44 768 / 1440 x 900 / 1600 x 900 / 1600 x 1200 / 1680 x 1050 / 1920 x 1080 / 1920 x 1200 LVDS Backlight Selects a level of brightness. Control Options: Level-0 ~ Level-7 ET880 Series User’s Manual...
- Page 45 Configuration Parallel Port Set parameters of parallel port (LPT/LPTE). Configuration 4.4.7.1 Serial Port 1 Configuration BIOS Setting Description Serial Port Enables / Disables the serial port. Change Settings Selects an optimal settings for Super I/O device. ET880 Series User’s Manual...
- Page 46 Changes the printer port mode. Device Mode Options: STD Printer Mode / SPP Mode / EPP-1.9 and SPP Mode / EPP-1.7 and SPP Mode / ECP Mode / ECP and EPP 1.9 Mode / ECP and EPP 1.7 Mode ET880 Series User’s Manual...
- Page 47 Change Settings Selects an optimal settings for Super I/O device. 4.4.8.2 Serial Port 2 Configuration BIOS Setting Description Serial Port Enables / Disables the serial port. Change Settings Selects an optimal settings for Super I/O device. ET880 Series User’s Manual...
- Page 48 Options: Disabled / 50C / 60C / 70C / 80C These fields are the parameters of the hardware Temperatures / monitoring function feature of the motherboard. The values are read-only values as monitored by Voltages the system and show the PC health status. ET880 Series User’s Manual...
- Page 49 “Auto” enumerates devices according to their KingstonDataTraveler media format. Optical drives are emulated as “CDROM”, drives with no media will be emulated 3.0PMAP according to a drive type. Options: Auto / Floppy / Forced FDD / Hard Disk / CD-ROM ET880 Series User’s Manual...
- Page 50 4.4.11 Network Stack Configuration BIOS Setting Description Network Stack Enables / Disables UEFI network stack. 4.4.12 NVME Configuration ET880 Series User’s Manual...
-
Page 51: Chipset Settings
Sets the aperture size as 128 MB, 256 MB, 512 MB, 1024 MB or 2048 MB. Note: Above 4 GB MMIO BIOS assignment is Aperture Size automatically enabled when selecting 2048 MB aperture. To use this feature, disable CSM support. VT-d Enable/Disable Vt-d capability ET880 Series User’s Manual... - Page 52 4.5.2 SATA Configuration: BIOS Setting Description SATA Controller(s) Enables / Disables the SATA device. SATA Mode Selection Determines how SATA controller(s) operate. Serial ATA Ports Enables / Disables SATA ports. Hot Plug Designates the port as Hot Pluggable. ET880 Series User’s Manual...
-
Page 53: Security Settings
Restore Forces system to user mode. Install factory default Factory Keys Secure Boot key databases. Enables expert users to modify Secure Boot Policy Management variables without full authentication. ET880 Series User’s Manual... - Page 54 Forces system to use mode. Restore Factory Keys Install factory default Secure Boot Key databases. Allow the image to run in Secure Boot mode. Enroll SHA256 Hash certificate of a PE image Enroll Efi Image into Authorized Signature Database (db). ET880 Series User’s Manual...
-
Page 55: Boot Settings
Number of seconds to wait for setup activation Setup Prompt key. Timeout 65535 (0xFFFF) means indefinite waiting. Bootup NumLock Selects the keyboard NumLock state. State Quiet Boot Enables / Disables Quiet Boot option. Fixed Boot Order Sets the system boot order. Priorities ET880 Series User’s Manual... -
Page 56: Save & Exit Settings
Saves the changes done so far as User Defaults. Restores the user defaults to all the setup Restore User Defaults options. Launch EFI Shell from Attempts to Launch EFI Shell application filesystem device (Sheel.efi) from one of the available filesystem devices. ET880 Series User’s Manual... -
Page 57: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. -
Page 58: I/O Port Address Map
Communications Port (COM3) 0x00000248-0x0000024F Communications Port (COM4) 0x00001800-0x000018FE Motherboard resources 0x00004090-0x00004097 Standard SATA AHCI Controller 0x00004080-0x00004083 Standard SATA AHCI Controller 0x00004060-0x0000407F Standard SATA AHCI Controller 0x00000020-0x00000021 Programmable interrupt controller 0x00000024-0x00000025 Programmable interrupt controller 0x00000028-0x00000029 Programmable interrupt controller ET880 Series User’s Manual... - Page 59 PCI Express Root Complex 0x00000D00-0x0000FFFF PCI Express Root Complex 0x0000EFA0-0x0000EFBF Intel(R) SMBus Controller - 4B23 0x00002000-0x000020FE Motherboard resources 0x00003000-0x00003FFF Intel(R) PCI Express Root Port #5 - 4B3D 0x00004000-0x0000403F Intel(R) UHD Graphics 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer ET880 Series User’s Manual...
-
Page 60: Interrupt Request Lines (Irq)
Interface #1 IRQ 4294967283~85 Intel(R) Ethernet Controller I226-IT Intel(R) I210 Gigabit Network IRQ 4294967286~91 Connection Intel(R) USB 3.10 eXtensible Host IRQ 4294967292 Controller - 1.20 (Microsoft) IRQ 4294967293 Intel(R) UHD Graphics IRQ 4294967294 Standard SATA AHCI Controller ET880 Series User’s Manual... -
Page 61: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81804 watch dog program\n"); SIO = Init_F81804(); if (SIO == 0) printf("Can not detect Fintek 81804, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); ET880 Series User’s Manual... - Page 62 DisableWDT(void) unsigned char bBuf; Set_F81804_LD(0x07); //switch to logic device 7 bBuf = Get_F81804_Reg(0xFA); bBuf &= ~0x01; Set_F81804_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81804_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81804_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- ET880 Series User’s Manual...
- Page 63 Init_Finish; F81804_BASE = 0x00; result = F81804_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81804 (void) outportb(F81804_INDEX_PORT, F81804_UNLOCK); outportb(F81804_INDEX_PORT, F81804_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81804 (void) outportb(F81804_INDEX_PORT, F81804_LOCK); //--------------------------------------------------------------------------- void Set_F81804_LD( unsigned char LD) Unlock_F81804(); outportb(F81804_INDEX_PORT, F81804_REG_LD); outportb(F81804_DATA_PORT, LD); Lock_F81804(); ET880 Series User’s Manual...
- Page 64 F81804_DATA_PORT (F81804_BASE+1) //--------------------------------------------------------------------------- #define F81804_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81804_UNLOCK 0x87 #define F81804_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81804(void); void Set_F81804_LD( unsigned char); void Set_F81804_Reg( unsigned char, unsigned char); unsigned char Get_F81804_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81804_H ET880 Series User’s Manual...
Need help?
Do you have a question about the ET880 Series and is the answer not in the manual?
Questions and answers