CY8CKIT-062-WIFI-BT About this document Scope and purpose This document explains about the CY8CKIT-062-WIFI-BT PSoC™ Wi-Fi Bluetooth® Pioneer Kit: kit operation, out- of the box example and its operation, and the hardware details of the board. Intended audience This evaluation board is intended for all technical specialists who are familiar with microcontrollers and connectivity and is intended to be used under laboratory conditions.
Boards provided by Infineon Technologies. The design of the Evaluation Boards and Reference Boards has been tested by Infineon Technologies only as described in this document. The design is not qualified in terms of safety requirements, manufacturing and operation over the entire operating temperature range or lifetime.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Safety precautions Safety precautions Note: Please note the following warnings regarding the hazards associated with development system Table 1 Safety precautions Caution: The evaluation or reference board contains parts and assemblies sensitive to electrostatic discharge (ESD).
PSoC™ 6 Wi-Fi Bluetooth® pioneer kit guide CY8CKIT-062-WIFI-BT Introduction Introduction Thank you for your interest in the CY8CKIT-062-WIFI-BT PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit. This kit enables you to evaluate and develop your applications using the PSoC™ 6 MCU. The PSoC™ 6 MCU is an ultra-low-power PSoC™ device specifically designed for wearables and IoT products. It is a programmable embedded system-on-chip, integrating a 150-MHz Arm®...
Getting started This guide will help you to get acquainted with the PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit: • “Kit operation” on page 20 describes the CY8CKIT-062-WIFI-BT baseboard and CY8CKIT-028-TFT shield hardware features and functionalities. • “Hardware” on page 35 provides a detailed hardware description, methods to use the onboard components, kit schematics, bill of materials (BOM), and FAQs.
Mount R162 (on the Pioneer Board) to connect J2.10 of the TFT board to P9[4]. Additional learning resources Infineon provides a wealth of data to help you to select the right PSoC™ device for your design and to help you to quickly and effectively integrate the device into your design.
PSoC™ 6 Wi-Fi Bluetooth® pioneer kit guide CY8CKIT-062-WIFI-BT Introduction Documentation conventions Table 3 Document conventions for guides Convention Usage Courier New Displays user entered text and source code Italics Displays file locations, file names, and reference documentation: Read about the sourcefile.hex file in the PSoC™ Creator user guide.
Page 19
PSoC™ 6 Wi-Fi Bluetooth® pioneer kit guide CY8CKIT-062-WIFI-BT Introduction Table 4 Acronyms used in this document (continued) Acronym Definition positive temperature coefficient pulse width modulation red green blue successive approximation register SMIF serial memory interface serial peripheral interface SRAM serial random access memory...
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation Kit operation This chapter introduces you to various features of the PSoC™ 6 Wi-Fi Bluetooth® Pioneer Board, including the theory of operation and the on-board KitProg3 programming and debugging functionality, USB-to-UART, USB- I2C and USB-SPI bridges.
Page 22
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation This Wi-Fi Bluetooth® Pioneer Kit comes with the PSoC™ 6 Wi-Fi Bluetooth® Pioneer Board, which has the CY8CKIT-028-TFT display shield connected, as Figure 7 shows. Figure 7 PSoC™ 6 Wi-Fi Bluetooth® Pioneer Board and TFT display shield Figure 8 shows the markup of the Pioneer Board.
Page 23
USB connector and the PC to use the KitProg3 on-board programmer and debugger and to provide power to the Pioneer Board. 4. Infineon EZ-PD™ CCG3 Type-C Port Controller with PD (CYPD3125-40LQXIT, U3): The Pioneer Board includes an EZ-PD™ CCG3 USB Type-C port controller with power delivery system. This device is preprogrammed and can deliver power from a Type-C port to an onboard header J16, while simultaneously charging a lithium-ion polymer battery connected to J15.
Page 24
25. Wi-Fi and Bluetooth® module (LBEE5KL1DX-883, U6): This kit features the on-board Wi-Fi and Bluetooth® combination module to demonstrate the IoT features. LBEE5KL1DX is a Type 1DX module available with 2.4-GHz WLAN and Bluetooth® functionality. Based on Infineon AIROC™ CYW4343W Wi-Fi & Bluetooth® combo chip, this module provides high-efficiency RF front-end circuits.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation 35. Battery connector (J15, on the bottom side of the board): This connector can be used to connect a lithium- ion polymer battery. Note that a battery is not included in the kit package and should be purchased separately if you want to demonstrate battery charging.
Page 26
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation The TFT display shield has the following peripherals: 1. 2.4-inch TFT display: This is a Newhaven 2.4-inch TFT LCD module with 240 × 320 pixel resolution and uses Sitronix ST7789 display controller.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation Note: The TFT display operation at 1.8 V is currently not supported in this version of the kit. Ensure that the following conditions are met when the CY8CKIT-028-TFT display shield is mounted on the PSoC™ 6 Wi-Fi Bluetooth®...
Page 28
Create new application b) Select the BSP in the Choose Board Support Package window and click Next. The rest of the steps uses the CY8CKIT-062-WIFI-BT BSP for the sake of explanation. Figure 13 Creating a new application: Choose board support package User guide 002-22677 Rev.
Page 29
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation c) Select the application in the Select Application window and click Create. Figure 14 Creating a new application: Select Application 4. To build and program a PSoC™ 6 MCU application, in the Project Explorer, select <App_Name> project. In the Quick Panel, scroll to the Launches section and click the <App_Name>...
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation 5. ModusToolbox™ software has an integrated debugger. To debug a PSoC™ 6 MCU application, in the Project Explorer, select <App_Name> project. In the Quick Panel, scroll to the Launches section and click the <App_Name>...
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation 5. On the Web Server Demo – Home Page, enter your Wi-Fi network name and password of the non-enterprise network directly or perform a Wi-Fi Scan to select the network you wish to use to connect to the cloud.
SPI connection between KitProg3 and PSoC™ 6 MCU EZ-PD™ CCG3 Type-C Power Delivery The Pioneer Board includes a Infineon EZ-PD™ CCG3 Power Delivery system. The EZ-PD™ CCG3 is pre-programmed and can deliver power from a Type-C port to the onboard header J16 (known as the consumer path), while simultaneously charging a 3.7-V, lithium-ion polymer battery connected to J15.
Page 33
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation D+/D‐ KitProg2 (PSoC 5LP) LED (o/p indication) Consumer control CCG3 charging current control VSYS Consumer External Terminal Path FET power o/p Block EZ‐PD CCG3 (Cypress) Provider control Load switch Provider Path with Slew rate VBUS control Monitor Monitor 5V @0.5A VBUS USB (Type C) 9V/ 12V @3A...
Page 34
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Kit operation Table 6 Type-C table power delivery scenarios USB host/Consumer Consumer Provider External USB PD Battery capability capability capability Out (J16 Header) charging current Non Type-C power <5 V 0 100 mA adapter (Legacy USB) >5 V...
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware Hardware Schematics See the schematic files available on the webpage. Hardware functional description This section explains the individual hardware blocks of the PSoC™ 6 Wi-Fi Bluetooth® Pioneer Board. 3.2.1 PSoC™ 6 MCU (U1) PSoC™...
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware 3.2.3 Serial interconnection between PSoC™ 5LP and PSoC™ 6 MCU In addition to being used as an on-board programmer, the PSoC™ 5LP MCU functions as an interface for the USB- UART, USB-I2C, and USB-SPI bridges, as shown in Figure 23.
Hardware 3.2.4 EZ-PD™ CCG3 power delivery system Infineon EZ-PD™ CCG3 provides a complete solution ideal for power adapters, power banks, Type-C dongles, monitors, docks, and notebooks. See “EZ-PD™ CCG3 Type-C Power Delivery” on page 32 for more details of the power delivery system implementation on the Pioneer Board.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware Figure 25 EZ-PD™ CCG3 power delivery setup using two CY8CKIT-062-Wi-Fi Bluetooth® kits 3.2.5 Power supply system The power supply system on this board is versatile, allowing the input supply to come from the following sources: •...
Page 39
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware Table 7 details the different powering scenarios for Pioneer Board. Table 7 Power supply scenarios Power inputs Board condition ETM header Battery JTAG/SWD Main PSoC™ Battery (VTARG_IN) connected header regulator powered...
Page 40
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware Figure 26 Schematics of power supply system User guide 002-22677 Rev. *J 2023-12-18...
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware 3.2.6 Expansion connectors 3.2.6.1 Headers compatible with Arduino (J1, J2, J3, J4, and J5) The board has five headers compatible with Arduino: J1, J2, J3, J4, and J5 (J5 is not populated by default). You can connect 3.3-V shields compatible with Arduino to develop applications based on the shield’s hardware.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware 3.2.7 CAPSENSE™ circuit A CAPSENSE™ slider and two buttons, all of which support both self-capacitance (CSD) and mutual-capacitance (CSX) sensing, and a CSD proximity sensor (header) are connected to PSoC™ 6 MCU as Figure 27 shows.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware 3.2.9 Push buttons The PSoC™ 6 Wi-Fi Bluetooth® pioneer kit has a reset button and three user buttons: • The reset button (SW1) is connected to the XRES pin of the PSoC™ 6 MCU, and is used to reset the device.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware 3.2.11 Quad SPI F-RAM The Pioneer Board contains the CY15B104QSN EXCELON™ F-RAM device, which can be accessed through Quad SPI interface. The F-RAM is 4-Mbit (512K × 8) and is capable of Quad SPI speed up to 108 MHz but the PSoC™ 6 MCU is limited to 80 MHz.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware 3.2.13 USB host and USB device connections The PSoC™ 6 MCU can be configured as either a USB host or USB device. When PSoC™ 6 is programmed as a host controller, you can connect an external device such as mouse, keyboard, and flash memory to the USB Type-A receptacle port (J27).
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware PSoC™ 6 Wi-Fi Bluetooth Pioneer Board reworks ® 3.3.1 Bypass protection circuit on program and debug header (J11) The 10-pin header allows you to program and debug the PSoC™ 6 MCU using an external programmer such as MiniProg4.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware Notes: 1. If you are programming the PSoC™ 6 MCU using a MiniProg4 connected to J11, make sure that the voltage is set at either 2.5 V or at 3.3 V.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Hardware 3.3.4 CAPSENSE™ shield The hatched pattern around the CAPSENSE™ buttons and slider are connected to ground. If liquid tolerance is required, this pattern needs to be connected to the shield pin. This pattern can be connected to either of the two ports P6.3 or P13.6 populated by R145 or R45, respectively.
8. I powered my board from Arduino by mistake while powering the PSoC™ 6 MCU. Is my PSoC™ 6 device alive? 9. I am unable to program the target device. 10. Does the kit get powered when I power it from another Infineon kit through the J1 header? 11. What additional overlays can be used with CAPSENSE™? 12.
Page 51
Ensure that the BSP selected in ModusToolbox™ software is CY8CKIT-062-WIFI-BT. 10. Is it possible to power the kit from another Infineon kit through the J1 header? Yes, VIN pin on the J1 header is the supply input/output pin and can support up to 12 V.
Page 52
Integrated, Analog Devices, and a variety of hobby sites. This kit supports only 1 × 6 pin interface compatible with Pmod. 13. What type of shield from Infineon is compatible with this baseboard? Any shield compatible with Arduino Uno that supports 3.3-V operation is compatible with this Pioneer Board. The following Infineon shields are pin-compatible with this board: •...
Page 53
9 V/12 V without a docking station. To use as a provider, any 5 V/9 V/12 V device that has a current requirement of less that 1 A may be used. Additionally, Infineon has its own USB Type-C evaluation kit, which can be used to evaluate the provider and consumer features and many more.
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Revision history Revision history Document Date of release Description of changes version 2018-02-21 New kit guide. Updated “Kit operation” on page 20: Updated “CY8CKIT-028-TFT details” on page 25: 2018-03-30 Updated “CY8CKIT-028-TFT display shield”...
Page 55
Updated description. ® Replaced “BT” with “Bluetooth ” in required instances across the document. Replaced “CY8CKIT-062-WiFi-BT” with “CY8CKIT-062-WIFI-BT” in all instances across the document. Updated Document Title to read as “CY8CKIT-062-WIFI-BT PSoC™ 6 Wi-Fi ® Bluetooth pioneer kit guide”. Updated “Introduction”...
Page 56
PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide CY8CKIT-062-WIFI-BT Revision history Document Date of release Description of changes version Removed “KitProg2”. Added “KitProg3: On-board programmer/debugger” on page 27. Removed “EZ-PD™ CCG3 Type-C Power Delivery”. Updated “NOR flash” on page 43: Replaced “Cypress NOR Flash” with “NOR Flash” in heading.
Page 57
CY8CKIT-062-WIFI-BT Revision history Document Date of release Description of changes version Migrated to IFX template. Updated Introduction Updated “CY8CKIT-062-WIFI-BT board details” on page 7: Updated Table 1 Updated “Theory of operation” on page 20 Updated “Programming and debugging using ModusToolbox™ software”...
All referenced product or service names and trademarks are the property of their respective owners. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Infineon is under license.