Infineon CY8CKIT-062-WIFI-BT Manual page 23

PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit guide
CY8CKIT-062-WIFI-BT
Kit operation
The PSoC™ 6 Wi-Fi Bluetooth® Pioneer Board has the following peripherals:
1. USB PD out indicator (LED7): This LED turns ON when the USB Type-C power delivery output is available for
use.
2. Battery charging indicator (LED6): This LED turns ON when the onboard battery charger is charging a
lithium-ion polymer battery connected to J15. Note that the battery connector and battery are not included
in the kit and should be purchased separately if you want to test the battery charging functionality.
3. KitProg3 USB connector (J10): The USB cable provided along with the PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit
connects between this USB connector and the PC to use the KitProg3 on-board programmer and debugger
and to provide power to the Pioneer Board.
4. Infineon EZ-PD™ CCG3 Type-C Port Controller with PD (CYPD3125-40LQXIT, U3): The Pioneer Board
includes an EZ-PD™ CCG3 USB Type-C port controller with power delivery system. This device is
preprogrammed and can deliver power from a Type-C port to an onboard header J16, while simultaneously
charging a lithium-ion polymer battery connected to J15. In addition, the power delivery system can deliver
power to a Type-C power sink or consumer, such as a mobile phone, with the power derived from the VIN
supply. See "EZ-PD™ CCG3 Type-C Power Delivery"
5. KitProg3 programming button (SW3): This button can be used to switch between the KitProg3 operation
modes (proprietary SWD programming/CMSIS-DAP mode).
6. KitProg3 I/O header (J6): This header brings out several GPIOs of the on-board KitProg3 PSoC™ 5LP device.
This includes the USB-I2C, USB-UART, and USB-SPI bridge lines. The additional PSoC™ 5LP MCU pins are
direct connections to the internal programmable analog logic of the PSoC™ 5LP MCU. For details on KitProg3,
see the KitProg3 user
7. KitProg3 programming (J7): This header brings out more GPIOs of the PSoC™ 5LP MCU. It also contains a
five-pin SWD programming header for the PSoC™ 5LP MCU.
8. External power supply VIN connector (J9): This connector connects an external DC power supply input to
the on-board regulators. The voltage input from the external supply should be between 5 V and 12 V.
9. PSoC™ 6 MCU user button (SW2): This button can be used to provide an input to the PSoC™ 6 MCU.
Note that by default the button connects the PSoC™ 6 MCU pin to ground when pressed, so you need to
configure the PSoC™ 6 MCU pin as a digital input with resistive pull-up for detecting the button press.
This button also provides a wake-up source from low-power modes of the device.
10. I/O header compatible with Digilent Pmod (J14): This header can be used to connect 1 × 6 pin modules
compatible with Digilent Pmod.
11. Power LED (LED4): This is the amber LED that indicates the status of power supplied to the board.
12. KitProg3 status LEDs (LED1, LED2, and LED3): Red, amber, and green LEDs (LED1, LED2, and LED3
respectively) indicate the status of KitProg3. For details on the KitProg3 status, see the
13. PSoC™ 6 MCU reset button (SW1): This button is used to reset the PSoC™ 6 MCU. It connects the PSoC™ 6
MCU reset (XRES) pin to ground.
14. PSoC™ 6 MCU I/O headers (J18, J19, and J20): These headers provide connectivity to PSoC™ 6 MCU GPIOs
that are not connected to the headers compatible with Arduino. Most of these pins are multiplexed with
on-board peripherals and are not connected to the PSoC™ 6 MCU by default. For detailed information on how
to rework the kit to access these pins, see
15. Power header compatible with Arduino (J1): This header powers the shields compatible with Arduino.
It also has a provision to power the kit though the VIN input.
16. PSoC™ 6 MCU debug and trace header (J12): This header can be connected to an embedded trace
macrocell (ETM)-compatible programmer/debugger.
17. I/O headers compatible with Arduino Uno R3 (J2, J3, and J4): These I/O headers bring out pins from the
PSoC™ 6 MCU to interface with the shields compatible with Arduino. Some of these pins are multiplexed with
on-board peripherals and are not connected to PSoC™ 6 MCU by default. For detailed information on how to
rework the kit to access these pins, see
User guide
guide.
Table
Table 1.
on page 32 for more details.
1.
23
KitProg3 user guide.
002-22677 Rev. *J
2023-12-18