Directed DIRECTECHS DB3 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. Directechs DB3
  6. Installation manual

Directed DIRECTECHS DB3 Installation Manual

For 2003 jeep liberty
Hide thumbs Also See for DIRECTECHS DB3:
Table of Contents

Advertisement

Quick Links

Download this manual
Functions compatible with the 2003 Jeep Liberty
Arm Factory Security
Brake Status (foot brake)
Control of aftermarket alarm with OEM remote
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Entry Monitoring ALL Door Pins
403.CHRYSLER2
Entry Monitoring Trunk/Hatch Pin
Ignition Status
Immobilizer Bypass-Data No Key Req'd
Parking Lights Control
Remote Start Takeover
SmartStart
Tach / RPM Output
v3.13
2003 Jeep Liberty

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DIRECTECHS DB3 and is the answer not in the manual?

Questions and answers

Related Manuals for Directed DIRECTECHS DB3

Summary of Contents for Directed DIRECTECHS DB3

  • Page 1 403.CHRYSLER2 v3.13 2003 Jeep Liberty Functions compatible with the 2003 Jeep Liberty Arm Factory Security Entry Monitoring Trunk/Hatch Pin Brake Status (foot brake) Ignition Status Control of aftermarket alarm with OEM remote Immobilizer Bypass-Data No Key Req'd Disarm Factory Security Parking Lights Control Door Lock Control Remote Start Takeover...

  • Page 2: Table Of Contents

    Contents Introduction Pre-installation and application warnings Wiring diagram Locating components in the vehicle Vehicle connections Module programming For Convenience-Only programming, see next section. Module programming for convenience only (skip transponder) Connecting the module LED diagnostics and troubleshooting Soft reset Hard reset Feature programming Feature and option list Limited one year consumer warranty...

  • Page 3: Introduction

    DB3 is an all-in-one door lock and override module. Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to “Connecting the module” for more information. 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 4: Pre-Installation And Application Warnings

    Vehicles with an OEM alarm: When flashing the interface, enable 'With OEM Alarm', under 'Data Configuration'. A resistor is required for parking lights. Refer to the Vehicle connections section for more details. 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 5: Wiring Diagram

    Refer to Vehicle Arm/Disarm connections section for (+) Acc. 1: Black/Orange or Pink/Yellow, pin 8 wire and connector details. (+) Acc. 2: Black/White, pin 7 (+) Starter: Yellow or Pink/Orange, pin 6 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 6: Locating Components In The Vehicle

    Locating components in the vehicle 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 7: Vehicle Connections

    BCM on rear right of dash fuse box, gray 22 pin plug, pin 9 Alarm) H2/10 Yellow/Black No Connection No Connection H2/11 Orange/Black No Connection No Connection H2/12 Blue/Red No Connection No Connection 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.
  • Page 8 Ignition Switch, black 10 pin plug, pin 7 Black/White Starter Ignition Switch, black 10 pin plug, pin 6 Yellow Tachometer [1] Camshaft Position Sensor, top of engine, black 3 pin plug, pin 3 Tan/Yellow (2.4L) 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 9: Module Programming

    3 seconds, and it will finally shut OFF. Turn the key to OFF, and remove it from the ignition barrel. You have successfully completed the module programming sequence. 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 10: Module Programming For Convenience Only (Skip Transponder)

    Turn the ignition ON and wait until the LED turns OFF. START Key OUT Turn ignition OFF and remove the key from the ignition barrel. START You have successfully completed the module programming sequence. 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 11: Connecting The Module

    4-pin D2D harness. (12-pin) (D2D) (10-pin) (14-pin) W2W installation If required: Connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module. (12-pin) (10-pin) (14-pin) 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 12: Led Diagnostics And Troubleshooting

    External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.
  • Page 13 The smart key was not detected, which prevents the system from shutting down the vehicle. Flashes red x 3 Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 14: Soft Reset

    Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts & to flash orange and red. Solid Flashes Release the programming button. The LED turns ON solid red. & Solid Release 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 15: Feature Programming

    To exit feature programming, press and hold the programming button for 3 seconds or ensure there is no activity on the interface for 30 seconds. The LED will turn ON orange for 2 seconds to confirm the end of the programming sequence. 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 16: Feature And Option List

    3. Enabled* status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 17: Limited One Year Consumer Warranty

    This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. VOXX DEI LLC, 2351 J. Lawson Blvd., Orlando, Florida 32824 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

  • Page 18: Quick Reference Guide

    + the panic mode. Press once, then to reset the x1 + remote starter runtime. * This output is configurable. see your authorized installation center for more information. 403.CHRYSLER2 3.13 2003 Jeep Liberty ©2023 Directed. All rights reserved.

Table of Contents