Advertisement

INSTALLATION GUIDE
DB3
2005 Lincoln LS. 403.FORD1 4.21
Designed by Installers for Installers
© 2020 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.

Advertisement

Table of Contents
loading

Summary of Contents for Directed DB3

  • Page 1 2005 Lincoln LS. 403.FORD1 4.21 Designed by Installers for Installers © 2020 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s...
  • Page 2: Table Of Contents

    Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Wiring diagram Locating components in the vehicle Vehicle connections Key2GO Disarm testing Connecting the module Module programming 2-Key programming NO Key2GO 1-Key programming using Key2GO LED diagnostics and troubleshooting Soft reset Hard reset Feature programming Feature and option list...
  • Page 3 The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.
  • Page 4: Introduction

    Introduction DB3 is an all-in-one door lock and override module. Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to “Connecting the module” for more information. Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
  • Page 5: Pre-Installation And Application Warnings

    The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. If present, CAN connections are ONLY required is using in conjunction with SmartStart. Warning: To avoid vehicle damage, refer to 'Vehicle connections' for parking light and Configuration. 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 6: Wiring Diagram

    RX: Orange/Black: 11 (-) Trunk/Hatch Release Output (+) Starter Output (+) Ignition Output RX: Gray/Red, pin 4 TX: White/Red, pin 3 PATS Transceiver (black conn. on ignition switch) 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 7: Locating Components In The Vehicle

    (-) Parking Lights: White/Blue or White/Green, pin 5 XKD2D65 (-) Parking Lights: Brown/Green, pin 7 Resistor 1800Ω Fuse 10A Refer to Vehicle Connections or go to www.directechs.com for more information on vehicle-specific wiring connections. 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 8: Vehicle Connections

    PATS Transceiver on ignition switch, green 4 pin plug, pin 4 Data Gray/Red H2/12 Blue/Red No Connection No Connection Input 10-pin black connector (H3) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 9 (Data) TX H4/2 Black (-) Ground H4/3 Green (Data) RX H4/4 (+) 12 Volt RF 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 No Connection H5/2 No Connection 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 10 Third Accessory Ignition Switch, black 8 pin plug, pin 4 Yellow Trunk/Hatch Release FEM in driver kick, 26 pin plug, pin 4 white 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 11: Key2Go

    Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO is compatible with XKLoader2 and the online web tool, as well as XKLoader3 and the Directechs Mobile application.
  • Page 12: Disarm Testing

    It is important to read through all the steps before proceeding. Note: This testing is to be done if you want to use the DB3 to disarm the factory alarm on unlock and trunk release. This install type can only be done on low current ignition switch and on vehicles that do not disarm using the key to unlock the driver's door. If using a one-button system or door locks are not being connected, the disarm will automatically be done upon remote start.
  • Page 13: Connecting The Module

    4-pin D2D harness. (12-pin) (D2D) (10-pin) (14-pin) W2W installation If required: Connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module. (12-pin) (10-pin) (14-pin) 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 14: Module Programming

    Turn vehicle ignition OFF once the module is successfully programmed. You have successfully completed the module programming sequence. 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 15: 1-Key Programming Using Key2Go

    Connect the module wiring to the vehicle first, and only then, plug the harnesses to the DB3 without pressing the programming button. The LED turns ON solid red. Insertthe key andthen turn the ignition ON and OFF twice. The LEDnow flashesorange.
  • Page 16: Led Diagnostics And Troubleshooting

    External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 17 The smart key was not detected, which prevents the system from shutting down the vehicle. Flashes red x 3 Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 18: Soft Reset

    Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the & LED starts to flash orange and red. Solid Flashes Release the programming button. The LED turns ON solid red. & Release Solid 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 19: Feature Programming

    To exit feature programming, press and hold the programming button for 3 seconds or ensure there is no activity on the interface for 30 seconds. The LED will turn ON orange for 2 seconds to confirm the end of the programming sequence. 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 20: Feature And Option List

    Module is connected to SmartStart using an RSR or RXT installation (when available). 1. Without OEM OEM Security The hood sensing feature is not available. alarm* Equipped 2. With OEM The hood sensing feature is available. alarm 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.
  • Page 21: Limited One Year Consumer Warranty

    This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
  • Page 22: Quick Reference Guide

    Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode.
  • Page 23 Notes 403.FORD1 4.21 2005 Lincoln LS © 2020-06-02 Directed. All rights reserved.

This manual is also suitable for:

Directechs db3

Table of Contents