Charging Times - Parkside Performance PPKSA 40-Li A1 Translation Of The Original Instructions

GB MT
Motor current I ................................16 A
Protection category...........................IPX0
Chain speed
v ........................... 15 m/s or 20 m/s
0
v ........................................25 m/s
max
Weight­­(without­saw­chain,­
blade­bar,­bade­encasing,­oil,­
rechargeable­batteries) ... approx.­3.17­kg
Oiltank ...................................... 180 ml
16" Chain bar . Trilink M1431656-1041TL
Chain ......................... Trilink CL14356TL
Chain pitch .................. 3/8"­(9,5­mm)
Chain link separation ............... 10 mm
Chain width ........................... 1.1 mm
Teeth of the sprocket chain wheel ....... 6
Length of the chain bar .455 mm/45,5 cm
Sawing length ... approx.­380 mm/38 cm
Temperature..........................max.­50 °C
Operation ......................... -20­-­50 °C
Storage ................................ 0­-­45 °C
Acoustic pressure level
) ....................... 91.3 dB; K
(L
pA
Sound power level (L
measured ....... 102.3 dB; K
guaranteed .............................105 dB
Vibration
) ......... max.­1.76­m/s
(a
h
Type of battery ............................... Li-Ion
For use with smart batteries
(Smart PAPS 204 A1/Smart PAPS 208 A1)
Operating frequency/
Frequency band ....2400­-­2483.5 MHz
Max.­transmission­power ...... ≤­20­dBm
Noise and vibration values were deter-
mined according to the standards and
stipulations mentioned in the declaration of
conformity.
The­specified­total­vibration­value­and­the­
stated noise emission value have been
measured according to a standardised test
method and can be used to compare one
power tool with another.
40
= 3 dB
pA
)
WA
= 2.37 dB
WA
; K= 1.5 m/s
2
The­specified­total­vibration­value­and­the­
stated­specified­noise­emission­value­can­
also be used for a provisional assessment
of the load.
Warning: The vibration and noise
emissions may deviate from the
specified­values­during­actual­use­of­the­
power­tool,­depending­on­how­the­power­
tool­is­being­used­and,­in­particular,­what­
kind of material is being worked on.
Safety measures for the protection of the
operator are to be determined that are
based on an estimate of the actual vibra-
tion load under the real operating condi-
tions­(for­this,­all­parts­of­the­operating­
cycle­are­to­be­taken­into­account,­for­
example,­times­in­which­the­electric­tool­
is­turned­off,­and­those­during­which­it­is­
turned­on­but­running­without­a­load).

Charging times

The­device­is­part­of­the­X­20­V­TEAM­
series from Parkside and can be operated
using­batteries­of­the­X­20­V­TEAM­series­
from­Parkside.­Batteries­of­the­X 20 V­
2
TEAM­series­may­only­be­charged­using­
chargers­of­the­X 20 V­TEAM­series.
We recommend that you operate this
appliance with the following batteries only:
PAP 20 B1,­PAP 20 B3,­
Smart PAPS 204 A1,­Smart PAPS 208 A1.
We recommend charging these batteries
with the following chargers:
PLG 20 A3,­PLG 20 C1,­PLG 20 C3,­
PLG 20 A4,­PLG 201 A1,­PDSLG 20 A1,­
PDSLG 20 B1,­Smart PLGS 2012 A1.