Table of Contents
Advertisement
Setting the language
Once the appliance has been connected to the power supply,
you must set the language for the text display.
Turn the temperature selector until the language you require
1.
appears on the text display.
Press and hold the
±
info button for 3 seconds.
2.
Your setting is saved.
Changing the language
Your appliance must be switched on.
If required, turn the operating mode selector to the
1.
Press and hold the
info button for 3 seconds.
±
2.
This takes you directly to the language selection screen.
Turn the temperature selector until the language you require
3.
appears on the text display.
Press and hold the
info button for 3 seconds.
±
4.
Your setting is saved.
Setting the clock
Note: When you press the
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
:
flashes in the clock display.
‹
‹‹
Briefly press the
clock function button to go to the
KJ
1.
setting mode.
The
and
symbols light up.
KJ
3
clock display.
Set the current time using the rotary selector.
2.
Your setting is accepted after 3 seconds.
Changing the clock
To subsequently change the time, press the
button repeatedly until the
Change the time with the rotary selector.
Setting the water hardness range
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
clock function button, you have
KJ
:
appears in the
‚ƒ
‹‹
clock function
KJ
and
symbols light up again.
KJ
3
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness "medium" (
Change the value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
Notes
If your water is very hard, we recommend that you use
■
softened water.
If you use only softened water, you can set your appliance to
■
the "softened" water hardness range.
If you use mineral water, set the water hardness to hard.
■
If you use mineral water, you must only use non-carbonated
■
mineral water (see section "Filling and emptying the water
tank").
You can change the water hardness range in the basic settings
when the appliance is switched on.
If required, turn the operating mode selector to the
1.
Press and hold the
2.
appears in the text display.
position.
Briefly press the
Û
3.
appears in the temperature display (water
hardness "medium").
Use the temperature selector to set the water hardness.
4.
Water hardness
softened
soft
medium
hard
very hard
Press and hold the
5.
Your setting is saved.
First use
Before first use, heat the empty appliance with
cooking for 20 minutes at 100 °C. Do not open the appliance
door during this time. The appliance is automatically calibrated
(see section: Automatic calibration).
Press the operating mode selector so that it pops out.
1.
The appliance switches on.
Fill and insert the water tank (see section: Filling the water
2.
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
Turn the operating mode selector round to
3.
cooking.
Press the Start button.
4.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
Press the
5.
Turn the operating mode selector back to the
6.
click in place to turn off the appliance.
Leave the appliance door ajar until the appliance has cooled
down.
) is the default setting.
™‡ƒ
±
info button until "Select language"
information button repeatedly until
±
Setting symbol (temperature dis-
play)
™‡‹
™‡‚
™‡ƒ
™‡„
™‡...
±
info button for 3 seconds.
clock function button to exit the clock function.
KJ
position.
Û
™‡ƒ
Steam
é
é
Steam
Û
position and
9
Advertisement
Table of Contents
