Danfoss VLT AQUA Drive FC 200 Operating Instructions Manual page 168

VLT AQUA Low Harmonic Drive Operating In-
structions
Mains Supply 3 x 380 - 480 VAC
Typical Shaft output at 400
V [kW]
Typical Shaft output at 460
V [HP]
Enclosure IP21, 54
Output current
Continuous
(at 400 V) [A]
Intermittent (60 sec over-
load)
(at 400 V) [A]
Continuous
(at 460/ 480 V) [A]
Intermittent (60 sec over-
load)
(at 460/ 480 V) [A]
Continuous KVA
(at 400 V) [KVA]
Continuous KVA
(at 460 V) [KVA]
Max. input current
Continuous
(at 400 V ) [A]
Continuous (at 460/ 480 V)
[A]
Max. cable size,motor
[mm 2
Max. cable size,mains F1/
F2 [mm
Max. cable size,mains F3/
F4 [mm
Max. cable size, loadshar-
ing [mm
Max. cable size, brake
2
[mm
Max. external pre-fuses [A]
1
Est. motor power loss at
rated max. load [W]
V, F1 & F2
Est. motor power loss at
rated max. load [W]
460 V, F1 & F2
Max added losses of A1
RFI, Circuit Breaker or Dis-
connect, & Contactor, F3 &
F4
Max Panel Options Losses
Weight,
enclosure IP21, IP 54 [kg]
Weight Drive
section [kg]
Weight Filter
section [kg]
Efficiency
Output frequency
Heatsink overtemp. trip
Power card ambient trip
1) For type of fuse see section
2) American Wire Gauge.
3) Measured using 5 m screened motor cables at rated load and rated frequency.
4) The typical power loss is at nominal load conditions and expected to be within +/-15% (tolerence relates to variety in voltage and cable
conditions). Values are based on a typical motor efficiency (eff2/eff3 border line). Motors with lower efficiency will also add to the power loss
in the frequency converter and opposite. If the switching frequency is increased comed to the default setting, the power losses may rise sig-
nificantly.LCP and typical control card power consumptions are included. Further options and customer load may add up to 30W to the losses.
(Though typical only 4W extra for a fully loaded control card, or options for slot A or slot B, each).
Although measurements are made with state of the art equipment, some measurement inaccuracy must be allowed for (+/-5%).
P500
500
650
F17
880
968
780
858
610
621
857
759
(AWG 2) )]
2 (AWG 2) )]
8x456
2 (AWG 2) )] (8x900 mcm)
2 (AWG 2) )]
2)
(AWG )
4) 10647
, 400
4) 9414
,
963
4)
Fuses.
®
MG.20.T1.02 - VLT is a registered Danfoss trademark
P560 P630
560 630
750 900
F17 F17
990 1120
1089 1232
890 1050
979 1155
686 776
709 837
964 1090
867 1022
8x150
(8x300 mcm)
8x240
(8x500 mcm)
4x120
(4x250 mcm)
4x185
(4x350 mcm)
1600
12338 13201
11006 12353
1054 1093
400
2009
1004
1005
0.96
0-600 Hz
95 °C
68 °C
8 General Specifications
P710
710
1000
F17
1260
1386
1160
1276
873
924
1227
1129
8
2000
15436
14041
1230
167