Table of Contents
Advertisement
Loewe bild 5 oled / bild 4 oled
User handbook
Miscellaneous
Important hints on the special features of
OLED technology
To maintain the high quality of picture display permanently, your Loewe
TV set calibrates itself automatically at regular intervals. In this way,
excess TFT capacitors are discharged and so-called image sticking
effects / „ghost images" are eliminated.
This calibration cycle will take a maximum of thirty minutes and starts
when your TV set is in standby mode. When switching the TV set off,
a screen text indicates that a pending refresh is due. In this case, do
not switch off the TV with its power switch and do not interrupt the
power supply.
Should such a calibration process be interrupted, it will be continued
when switching off the TV set next time. You still have the possibility
to start a refresh procedure manually by means of the user menu of
your Loewe TV set.
Call OLED calibration
HOME: Call Home view.
Select System settings,
OK call System settings.
Select Picture,
go to next column.
Select more ...,
call other settings.
Select OLED calibration,
OK Call.
Every 1500 hours, a calibration of OLEDs is necessary. This is done
automatically as soon as the switched off TV set is cooled down. The
procedure takes about two hours. Again, you will be previously infor-
med by an on-screen display.
To avoid temporary impairments of the picture display by long-lasting
still pictures, your Loewe TV set protects itself automatically. When still
images are displayed too long (for example, forgotten videotext pages),
the TV set automatically switches to a screen-friendly contrast mode.
After a new user operation, the device immediately returns to its nor-
mal state. In addition, each menu display is terminated automatically
when the TV set detects no operation for more than three minutes.
OLED technology allows for a design with an extremely thin display.
When you have mounted your Loewe TV set on a non-motorized in-
stallation option, avoid a too excessive force when rotating the TV set.
VESA standard
Instructions on using third-party mounting options according
to the VESA standard
Loewe flat screen TV sets are specified for Loewe accessories. When
using third-party mounting options according to the VESA standard,
the manufacturer's instructions on the mounting options must be
observed.
Loewe accepts no liability for the use of mounting options from other
manufacturers.
On the rear wall of the TV set, there are four points of screw connections
to receive the VESA adapter bolts.
Mounting a Loewe flat screen TV set to a holder according to the VESA
standard necessarily requires the use of Loewe VESA adaptor bolts.
Otherwise, the TV set may be damaged.
Screw the Loewe VESA adapter bolts with a torque of approx. 4 Nm
into the screwing points of the TV rear panel (see Fig. 1).
First, possibly existing screws in the four screwing points must be
removed.
1
The Loewe VESA adaptor bolts are used to ensure stability and the
necessary minimum distance of 5 mm between rear wall of the TV
set and VESA holder (see Fig. 2). The VESA holder must not rest on
the rear panel.
When mounting the TV set, always check that all four Loewe VESA
adaptor bolts are used. For each mounting point, only one VESA
adapter bolt may be used. It is inadmissible to screw several VESA
adapter bolts or extend individual adapter bolts.
Measure the hole distance between the screwing points of your TV
set. A hole distance of 400 x 400 mm on the rear of the TV set means
VESA 400 standard.
Thus, a suitable mount bracket must also correspond to the VESA 400
standard. If the VESA standard of your TV set fits the standard of the
desired bracket, the bracket has also to be approved for the weight
and size of the TV set (for weight and TV set size refer to chapter
Technical Data).
Loewe is not responsible for the permissible load-carrying capacity
and the professional fixing of the holder.
Please observe additionally and definitely the points described in the
chapter on safety instructions.
If you use a Vesa mounting options from other manufacturers, you
can order the Vesa adapter bolts M6x32 (No. 90473.988) at your
authorized dealer of Loewe.
2
139
Advertisement
Table of Contents
