Table of Contents
Advertisement
11.36 "Connection code"
Pump variant
NBE, NBSE, NKE, TPE, TPED
NBE, NBSE, NKE, TPE, TPED
Series 2000
This menu is only available in Grundfos GO.
You can set a connection code to avoid having to press the
connection button each time and to restrict remote access to the
product.
Setting the code in the product using Grundfos GO
1. Connect Grundfos GO to the product.
2. In the product dashboard, select "Settings".
3. Choose "Connection code".
4. Enter the wanted code and press [OK].
The code must be a character string, ASCII. You can always
modify the code. The old code is not needed.
Setting the code in Grundfos GO
You can set a default connection code in Grundfos GO so that it
automatically attempts to connect to the selected product via this
code.
When you select a product with the same connection code in
Grundfos GO, Grundfos GO automatically connects to the
product and you do not have to press the connection button on
the module.
Set the default code in Grundfos GO in this way:
1. In the main menu, under "General", select "Settings".
2. Choose "Remote".
3. Enter the connection code in the field "Preset connection
code". The field now says "Connection code set".
You can always modify the default connection code by pressing
[Delete] and entering a new one.
If Grundfos GO fails to connect and ask you to press the
connection button on the product, it means that the product has
no connection code or has a different connection code. In this
case, you can only establish connection via the connection
button.
After setting a connection code, you must switch off the product
until the light in Grundfos Eye turns off before you can use the
new connection code.
Factory setting
See section
28. Factory
settings.
42
"Connection code"
●
●
11.37 Run start-up guide
Pump variant
NBE, NBSE, NKE, TPE, TPED
NBE, NBSE, NKE, TPE, TPED
Series 2000
This menu is only available in the advanced control panel.
The startup guide automatically starts when you start the pump
for the first time.
You can always run the startup guide later via this menu.
The startup guide guides you through the general settings of the
pump.
Language. See section
•
11.25
Select date format.
•
See section
11.26 "Date and time" (
•
Set date.
See section
11.26 "Date and time" (
Select time format.
•
See section
11.26 "Date and time" (
•
Set time.
See section
11.26 "Date and time" (
Setting of pump
•
– Go to Home
– Run with Constant curve/Run with Constant pressure.
See section
11.5 "Control mode"
– Go to "Assisted pump setup".
Assisted pump setup
See section
11.41
– Return to factory settings.
* Applies only for pumps with advanced functional module, FM
300. For further information, see section
functional
module.
11.38 Alarm log
Pump variant
NBE, NBSE, NKE, TPE, TPED
NBE, NBSE, NKE, TPE, TPED
Series 2000
This menu contains a list of logged alarms from the product. The
log shows the name of the alarm, when the alarm occurred and
when it was reset.
11.39 Warning log
Pump variant
NBE, NBSE, NKE, TPE, TPED
NBE, NBSE, NKE, TPE, TPED
Series 2000
This menu contains a list of logged warnings from the product.
The log shows the name of the warning, when the warning
occurred and when it was reset.
11.40 Assist
Pump variant
NBE, NBSE, NKE, TPE, TPED
NBE, NBSE, NKE, TPE, TPED
Series 2000
The menu consist of functions which take you through the steps
needed to set the pump.
Run start-up guide
●
●
Language
.
Set date and time
).
Set date and time
).
Set date and time
).
Set date and time
).
.
18. Identification of
Alarm log
●
●
Warning log
●
●
Assist
●
●
Advertisement
Table of Contents
