"Settings"
"Setpoint"
"Operating mode"
"Set user-defined speed"
"Control mode"
"Proportional-pressure
setup"
"Buttons on product"
"Controller"
"Operating range"
"Ramps"
"Pump number"
"Radio communication"
"Analog input 1"
"Analog input 2"
"Analog input 3"
"Built-in Grundfos sensor"
"Pt100/1000 input 1"
"Pt100/1000 input 2"
"Digital input 1"
"Digital input 2"
"Digital in/output 3"
"Digital in/output 4"
"Predefined setpoint"
"Analog output"
"External setpoint funct."
"Signal relay 1"
"Signal relay 2"
"Limit 1 exceeded"
"Limit 2 exceeded"
"Alternating operation, time"
"Time for pump
changeover"
"Standstill heating"
"Motor-bearing monitoring"
"Service"
"Date and time"
"Store settings"
"Recall settings"
"Undo"
"Pump name"
"Connection code"
"Unit configuration"
1)
Only available if Grundfos GO is connected to a multipump system.
2)
Applies only to a multipump system with NBE, NBSE, NKE, TPE, TPED Series 2000 pumps.
22
NBE,
NBE,
NBSE,
NBSE,
NKE, TPE,
Multipump
NKE, TPE,
TPED
system
TPED
Series
2000
●
●
●
●
●
●
●
●
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
-
-
-
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Section
Setpoint
●
11.1
Operating mode
●
11.2
●
11.4 "Set user-defined speed"
●
11.5 "Control mode"
-
11.6 "Proportional-pressure setup"
11.28 "Buttons on product" (
●
settings
)
●
11.14 "Controller" ("Controller settings")
Operating range
●
11.15
11.19 "Ramps"
Pump number
-
11.23 "Number" (
11.24 "Radio communication"
-
(Enable/disable radio comm.)
-
Analog inputs
-
11.7
-
2)
●
11.8 Built-in Grundfos sensor
-
Pt100/1000 inputs
11.9
-
-
Digital inputs
11.10
-
-
Digital inputs/outputs
11.11
-
●
11.16.2 "Predefined setpoints"
Analog output
-
11.13
-
11.16.2 "Predefined setpoints"
-
11.12 "Signal relays 1 and 2" (
outputs
-
)
●
Limit-exceeded function
11.17
●
1)
●
11.43 "Multipump setup" (
multi-pump system
1)
●
)
-
11.20 "Standstill heating"
Motor bearing monitoring
-
11.21
-
11.22 "Service"
●
11.26 "Date and time" (
11.32 "Store settings" (
-
settings
)
11.33 "Recall settings" (
-
settings
)
●
11.34 "Undo"
●
11.35 "Pump name"
●
11.36 "Connection code"
●
11.27 "Unit configuration" (
Page
24
24
24
24
28
Enable/disable
41
34
36
39
40
)
40
29
30
30
31
32
38
33
36
Relay
33
38
Setup of
43
39
40
40
Set date and time
40
)
Store actual
41
Recall stored
41
41
41
42
Units
40
)