Spectra Logic T-Series Spectra T120 Supplementary Manual

Spectra Logic T-Series Spectra T120 Supplementary Manual

G4/g5 qip upgrade and encrypted media guide for spectra t120 and spectra t950 libraries
Hide thumbs Also See for T-Series Spectra T120:

Advertisement

Quick Links

G4/G5 QIP Upgrade and
Encrypted Media Guide
for
Spectra T120 and Spectra T950 Libraries
PN 90940020 Revision B

Advertisement

Table of Contents
loading

Summary of Contents for Spectra Logic T-Series Spectra T120

  • Page 1 G4/G5 QIP Upgrade and Encrypted Media Guide Spectra T120 and Spectra T950 Libraries PN 90940020 Revision B...
  • Page 2 Information furnished in this manual is believed to be accurate and reliable. However, no responsibility is assumed by Spectra Logic for its use. Due to continuing research and development, Spectra Logic may revise this publication from time to time without notice, and reserves the right to change any product specification at any time without notice.
  • Page 3: Table Of Contents

    Contents Introduction ............4 Using Media Encrypted with G3 and G5 QIPs .
  • Page 4: Introduction

    Introduction The G4 and G5 QIP supports 4 GB Fibre Channel, and may require a library firmware upgrade. • The G4 QIP does not support BlueScale Encryption and key management. • The G5 QIP supports BlueScale Encryption and key management. The upgrade process involved in moving from the G2/3 to the G4/5, including use of media encrypted using G3 and G5, is reviewed in this guide.
  • Page 5: Materials And Tools Required

    • A #2 Phillips screwdriver Note: After unpacking the upgrade kit, save the packaging. You will need it to pack up the old QIP and the above listed tools for return to Spectra Logic. Estimated Time Required This procedure takes about ten minutes.
  • Page 6: Overview Of Qip Upgrade Process

    Overview of QIP Upgrade Process The G4/G5 QIP lets you connect your Spectra T120 or T950 library to 4Gb Fibre Channel HBAs and switches, which can support data transmission rates of up to 4 gigabits per second. The entire upgrade process requires only these steps, described in more detail through this guide: 1.
  • Page 7: Removing The G2/G3 Qip

    Removing the G2/G3 QIP 1. Use your backup software to stop backups running on the library. 2. Use the soft power button on the front of the library to shut down power to the library. 3. Shut off the AC power switch on the back of the library. 4.
  • Page 8: Removing The G2/G3 Qip Pin

    Removing the G2/G3 QIP Pin 1. Attach the ratchet to one end of the extender, and the bolt extractor to the other end of the extender, as shown in Figure 2. 2. Make sure that the ratchet is set for loosening.
  • Page 9: Installing The G4/G5 Qip Pin

    G4/G5 QIP Upgrade and Encrypted Media Guide Installing the G4/G5 QIP Pin 1. Remove the bolt extractor from the end of the extender. 2. Set the ratchet to tighten. 3. Attach the deep-well socket to the other end of extender. 4.
  • Page 10: Installing The G4/G5 Qip

    G4/G5 QIP Upgrade and Encrypted Media Guide Installing the G4/G5 QIP 1. Carefully unwrap the G4/G5 QIP from its anti-static bag. 2. Use the QIP’s handle to place the QIP into its bay. 3. Push the QIP gently but firmly inward until it clicks into place. 4.
  • Page 11: Finish

    Finish 1. Turn on the AC power switch on the back of the library. 2. Turn on the library using the soft power switch on the front of the library. 3. Wait for the library to come ready. 4. Go to the front of the library and log in to the LC. The Messages screen may indicate that you need to upgrade firmware.
  • Page 12: Returning The G2/G3 Qip

    Returning the G2/G3 QIP Package the G2/G3 QIP and the tools used for the upgrade in the same packaging that Spectra Logic used to send you the upgrade parts. Make sure to use all of the packing materials provided to prevent damage during shipment.

This manual is also suitable for:

T950

Table of Contents