Advertisement

Quick Links

Copyright
Copyright © 2023 MITAC COMPUTING TECHNOLOGY CORPORATION. All rights
reserved. No part of this manual may be reproduced or translated without prior
written consent from MITAC COMPUTING TECHNOLOGY CORPORATION.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
®
TYAN
is a trademark of MITAC COMPUTING TECHNOLOGY CORPORATION.
®
Intel
is a trademark of Intel
AMI, AMI BIOS are trademarks of AMI Technologies.
Microsoft
®
, Windows
®
Nuvoton
is a trademark of Nuvoton Technology Corporation.
Notice
Information contained in this document is furnished by MITAC COMPUTING
TECHNOLOGY CORPORATION and has been reviewed for accuracy and reliability
prior to printing. MITAC assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of TYAN
or warranties relating to fitness for a particular purpose or merchantability. MITAC
retains the right to make changes to product descriptions and/or specifications at
any time, without notice. In no event will MITAC be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.
S5565
Version 1.0
®
Corporation.
®
are trademarks of Microsoft Corporation.
http://www.tyan.com
®
products including liability
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TYAN S5565 and is the answer not in the manual?

Questions and answers

Summary of Contents for MiTAC TYAN S5565

  • Page 1 In no event will MITAC be held liable for any direct or indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting from errors or inaccuracies of information contained in this document.
  • Page 2 http://www.tyan.com...
  • Page 3: Table Of Contents

    Contents Before you begin… ..................4   Chapter 1: Instruction ................5   1.1 Congratulations ................. 5   1.2 Hardware Specifications ..............5   1.3 Software Specifications ..............7   Chapter 2: Board Installation ..............9   2.1 Board Image ..................10  ...
  • Page 4: Before You Begin

    Before you begin… Check the box contents! The retail motherboard package should contain the following: 1 x S5565 Motherboard 2 x SATA Cable 1 x M.2 Board Latch 1 x Rear IO Shield 1 x S5565 Quick reference guide IMPORTANT NOTE: Sales sample may not come with the accessory listed above.
  • Page 5: Chapter 1: Instruction

    TYAN products as well as all the supporting documentation, FAQs, Drivers and BIOS upgrades. 1.2 Hardware Specifications TYAN S5565 (S5565AG2NR) Q'ty / Socket Type (1) LGA1700 Supported CPU Series Intel Core i9/i7/i5/i3 Processors / 12 Gen.
  • Page 6 RAID VMD RAID 0/1/10/5 (Intel RST/VMD) Storage NVMe Connector (M.2) (2) 22110/2280 (by PCIe Gen.3 interface) Connector type (3) Display ports Graphic Display Resolution Up to 4096X2304 @60Hz Port Chipset Intel Processor Graphics (1) USB2.0 header / (1) USB3.2 Gen.1 header / (2) USB2.0 ports / (4) USB3.2 Gen.1 ports RJ-45...
  • Page 7: Software Specifications

    Operating OS supported list Please refer to our AVL support lists. System Motherboard (1) S5565 Motherboard Manual (1) Quick Installation Guide Package Contains I/O Shield (1) I/O Shield Cable SATA (2) SATA signal cables 1.3 Software Specifications ® For OS (operation system) support, please check with TYAN support for latest information.
  • Page 8 NOTE http://www.tyan.com...
  • Page 9: Chapter 2: Board Installation

    Unplug the power from your computer power supply and then touch a safely grounded object to release static charge (i.e. power supply case). For the safest conditions, MITAC recommends wearing a static safety wrist strap. (2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex the board in any way.
  • Page 10: Board Image

    2.1 Board Image S5565 This picture is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above picture. http://www.tyan.com...
  • Page 11: Block Diagram

    2.2 Block Diagram S5565 Block Diagram http://www.tyan.com...
  • Page 12: Mainboard Mechanical Drawing

    2.3 Mainboard Mechanical Drawing http://www.tyan.com...
  • Page 13: Board Parts, Jumpers And Connectors

    2.4 Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. But for the DIMM number please refer to the above placement for memory installation. For the latest board revision, please visit our web site at http://www.tyan.com.
  • Page 14 Jumpers & Connectors Connector 16 Power Connector Pin-out 1 Intrusion Header (INTRUD1) (PWR1) 2 M.2 Connector (M.2#1) PCIE ONLY 17 SYS_FAN_1 (SYS_FAN1) 18 Front Panel Pin Header 3 M.2 Connector (M.2#2) PCIE ONLY (FPIO1) 4 USB 3.2 Gen1 Header (USB3_FPIO1) 19 CPU_FAN (CPU_FAN1) 20 COM2 Port Header 5 SATA0 Connector (SATA0)
  • Page 15 SATADOM0~1: SATA DOM Header Signal GND/5VDC 5VDC SATA0/1/4/5: 7-pin SATA Connector Signal USB3_FPIO1: Front USB3.0 Header Signal Signal P0_RX_N P0_RX_P P1_RX_N P1_RX_P P0_TX_N P0_TX_P P1_TX_N P1_TX_P P0_N P0_P P1_N OC_N P1_P FPIO1: Front Panel Header Signal Signal HDD_LED_P GRN_BLNK_HRD HDD_LED_N YLW_BLNK_HRD FP_PWR_BTN_N FP_RST_BTN_N...
  • Page 16 HD_COM1 / HD_COM2: COM Port Header Signal Signal COM2_DCD COM2_DSR COM2_RXD COM2_RTS COM2_TXD COM2_CTS COM2_DTR COM2_NRI FAN1~FAN4 (CPUFAN1, SYSFAN1~3): 4-pin FAN Header Signal P12V FAN_TACH   FAN_PWM DBG_HD1: TPM Module Header Signal Signal VCC3_AUX TPM_CLK KTPM_PRSNT TPM_RST TPM_PRIQ_N TPM_MOSI VCC3 TPM_MISO TPM_CS2 EMPTY...
  • Page 17 J26: Power Button Signal Signal PWR_BTN1 J24: Reset Button Signal Signal FP_RST_BTN_N TYPEA_USB3: Vertical Type-A USB3.0 Connector Pin1 Pin2 Pin3 Pin4 Pin5 5VDC Pin6 Pin7 Pin8 Pin9 GND1 GND2 USB2_FPIO1: Front USB2.0 Header (black) Signal Signal 5VDC 5VDC J6: ESPI Port 80 Header Signal Signal P3V3_AUX...
  • Page 18 J7: System Buzzer Jumper Pin1 Pin2 Pin3 Pin4 VCC5_AUX BUZ_1 BUZ_2 Pin3-4 closed: Normal Mode (Default) Pin2-3 closed: Disable PC Beep Pin1-4 closed: Use the external speaker CMOS1: RTC Reset Header for Clear CMOS Signal PCH_RTCRST_N You can reset the CMOS settings by using this jumper. This can be useful if you have forgotten your system/setup password, or need to clear the system BIOS setting.
  • Page 19 M.2#1~2: M.2 Header (Slot) Signal Name Signal Name P3V3 P3V3 PERN3 PERP3 I/O/LED PETN3 P3V3 PETP3 P3V3 P3V3 PERN2 P3V3 PERP2 PETN2 PETP2 PERN1 PERP1 PETN1 PETP1 M2_SMB_CLK2 PERN0 M2_SMB_DAT2 PERP0 PETN0 PETP0 M2_PERST_N REFCLKN REFCLKP NC21 P3V3_AUX 3.3V 3.3V http://www.tyan.com...
  • Page 20 3.3V PCIE#3: PCIEX16 Header (Slot) Signal Name Signal Name PRSNT1# SMCLK JTAG2 SMDAT JTAG3 JTAG4 JTAG5 JTAG1 P3V3_AUX WAKE# PERST# RSVD_1 REFCLK+ PETp0 REFCLK- PETn0 PERp0 PRSNT2# PERn0 PETp1 RSVD_4 PETn1 PERp1 PERn1 PETp2 PETn2 PERp2 PERn2 PETp3 PETn3 PERp3 RSVD_2 PERn3 PRSNT2#_2...
  • Page 21 PERn4 PETp5 PETn5 PERp5 PERn5 PETp6 PETn6 PERp6 PERn6 PETp7 PETn7 PERp7 PRSNT2#_3 PERn7 PETp8 RSVD_7 PETn8 PERp8 PERn8 PETp9 PETn9 PERp9 PERn9 PETp10 PETn10 PERp10 PERn10 PETp11 PETn11 PERp11 PERn11 PETp12 PETn12 PERp12 PERn12 PETp13 PETn13 PERp13 PERn13 PETp14 PETn14 PERp14 PERn14...
  • Page 22 RSVD_3 PCIE#1~2: PCIEX8 Header (Slot) Signal Name Signal Name PRSNT1# SMCLK JTAG2 SMDAT JTAG3 JTAG4 JTAG5 JTAG1 V3AUX WAKE# PERST# RSVD_1 REFCLK+ PETp0 REFCLK- PETn0 PERp0 PRSNT2# PERn0 PETp1 RSVD_4 PETn1 PERp1 PERn1 PETp2 PETn2 PERp2 PERn2 PETp3 PETn3 PERp3 RSVD_2 PERn3 PRSNT2#_2...
  • Page 23 PRSNT2#_3 http://www.tyan.com...
  • Page 24: Led Definitions

    2.5 LED Definitions Signal VCC3 HDD_ACT_LED_N SATA & M.2 HDD_LED1 State Description HDD non-activity Blue HDD activity Signal VCC3 M2_1_LED_N LED1 M.2_1 LED State Description HDD non-activity Blue HDD activity Signal VCC3 M2_2_LED_N LED2 M.2_2 LED State Description HDD non-activity Blue HDD activity http://www.tyan.com...
  • Page 25: Installing The Processor And Heat Sink

    Specifications on page 5. Check our website at http://www.tyan.com for latest processor support. NOTE: MITAC TYAN is not liable for damage as a result of operating an unsupported configuration. Installing Processor (in Socket LGA1700) Follow the steps below to install the processors and heat sinks. NOTE: Please save and replace the CPU protection cap when returning for service.
  • Page 26 3. Align and seat the processor package on the socket. Make sure the gold arrow is located in the right direction. 4. Close the load plate. 5. Remove and save the ILM cover. 6. Close the ILM lever and latch. http://www.tyan.com...
  • Page 27 Removing Processor 1. Open the ILM lever and then the load plate using the finger tab. 2. Place the ILM cover and then carefully remove the processor package. 3. Close the load plate and latch the ILM lever. http://www.tyan.com...
  • Page 28 Heat sink Installation After installing the processor, you should proceed to install the heat sink. The CPU heat sink will ensure that the processor do not overheat and continue to operate at maximum performance for as long as you own them. The overheated processor is dangerous to the motherboard.
  • Page 29 Secure the heat sink screws. Connect the fan cable to complete the installation. http://www.tyan.com...
  • Page 30: Thermal Interface Material

    2.7 Thermal Interface Material There are two types of thermal interface materials designed for use with the processors. The most common material comes as a small pad attached to the heat sink at the time of purchase. There should be a protective cover over the material.
  • Page 31: Tips On Installing Motherboard In Chassis

    Some chassis include plastic studs instead of metal. Although the plastic studs are usable, MITAC recommends using metal studs with screws that will fasten the motherboard more securely in place. Below is a chart detailing what the most common motherboard studs look like and how they should be installed.
  • Page 32 http://www.tyan.com...
  • Page 33: Installing The Memory

    2.9 Installing the Memory Before installing memory, ensure that the memory you have is compatible with the motherboard and processor. Check the TYAN Web site at http://www.tyan.com details of the type of memory recommended for your motherboard.  Support (1) DIMM slots per channel ...
  • Page 34 Recommended Memory Population Table Single CPU Installed Q’ty of Memory Installed √ √ √ P0_ CHA_DIM0 √ P0_ CHA_DIM1 √ √ P0_CHB_DIM0 √ P0_CHB_DIM1 NOTE: 1.√ indicates a populated DIMM slot. 2. Use paired memory installation for max performance. 3. Populate the same DIMM type in each channel, specifically - Use the same DIMM size - Use the same # of ranks per DIMM 4.
  • Page 35 Memory Installation Procedure Follow these instructions to install memory modules into the S5565. 1. Unlock the clips. 2. Insert the memory module. 3. Lock the clips. http://www.tyan.com...
  • Page 36: Attaching Drive Cables

    2.10 Attaching Drive Cables Attaching Serial ATA Cables S5565 is equipped with four (4) Serial ATA (SATA) channel. Connections for the drives are very simple. There is no need to set Master/Slave jumpers on SATA drives. If you are in need of SATA/SAS cables or power adapters please contact your place of purchase.
  • Page 37: Installing Add-In Cards

    2.11 Installing Add-In Cards Before installing add-in cards, it’s helpful to know if they are fully compatible with your motherboard. For this reason, we’ve provided the diagrams below, showing the slots that may appear on your motherboard. Simply find the appropriate slot for your add-in card and insert the card firmly. Do not force any add-in cards into any slots if they do not seat in place.
  • Page 38: Connecting External Devices

    2.12 Connecting External Devices Connecting external devices to the motherboard is an easy task. The motherboard supports a number of different interfaces through connecting peripherals. See the following diagrams for the details. Onboard LAN LED Color Definition two (2) onboard Ethernet ports have green Yellow LEDs to indicate LAN...
  • Page 39 1G RJ45 Connector (LAN2) Diagram Color State Condition LAN link is not established LAN link is Link established Green LAN activity Blinking occurring 10 Mb/s data rate 100 Mb/s data Green Speed rate 1000 Mb/s data Orange rate http://www.tyan.com...
  • Page 40: Installing The Power Supply

    2.13 Installing the Power Supply There are two (2) power connectors on your S5565 motherboard. The S5565 supports EPS 12V power supply. NOTE: You must unplug the power supply before plugging the power cables to motherboard connectors. PWR1: ATX 24-pin Main Power Connector Signal Signal VCC3...
  • Page 41: Chapter 3: Bios Setup

    Chapter 3: BIOS Setup 3.1 About the BIOS The BIOS is the basic input/output system, the firmware on the motherboard that enables your hardware to interface with your software. The BIOS determines what a computer can do without accessing programs from a disk. The BIOS contains all the code required to control the keyboard, display screen, disk drives, serial communications, and a number of miscellaneous functions.
  • Page 42 Chipset section unless you are absolutely sure of what you are doing. The Chipset defaults have been carefully chosen either by MITAC or your system manufacturer for best performance and reliability. Even a seemingly small change to the Chipset setup options may cause the system to become unstable or unusable.
  • Page 43: Main Menu

    3.2 Main Menu In this section, you can alter general features such as the date and time. Note that the options listed below are for options that can directly be changed within the Main Setup screen. BIOS Information It displays BIOS related information. Memory Information This displays the installed memory size, and the installed memory frequency.
  • Page 44: Advanced Menu

    3.3 Advanced Menu This section facilitates configuring advanced BIOS options for your system. CPU Configuration CPU Configuration Parameters. PCH-FW Configuration Configure Management Engine Technology Parameters. Trusted Computing Trusted Computing Settings. ACPI Settings System ACPI Parameters. Watchdog Timer Configuration Watchdog Configuration. NCT6796D Super IO Configuration System Super IO Chip Parameters.
  • Page 45 Hardware Health Configuration Monitor Hardware Status. S5 RTC Wake Settings Enable system to wake from S5 using RTC alarm. Serial Port Console Redirection Serial Port Console Redirection. Option ROM Dispatch Policy Option ROM Dispatch Polic. PCI Subsystem Settings PCI, PCI-X and PCI Express Settings. USB Configuration USB Configuration Parameters.
  • Page 46 3.3.1 CPU Configuration CPU Configuration Read only. Hyper-Threading Enable or Disable Hyper-Threading Technology. Enabled / Disabled Active Performance-cores Number of P-cores to enable in each processor package. Note: Number of Cores and E-cores are looked at together. When both are {0, 0}, P-code will enable all cores.
  • Page 47 Intel (VMX) Virtualization Technology When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Enabled / Disabled Intel Trusted Execution Technology Enables utilization of additional hardware capabilities provided by Intel® Trusted Execution Technology. Changes require a full power cycle to take effect. Enabled / Disabled Boot Performance Mode Select the performance state that the BIOS will set starting from reset vector.
  • Page 48 3.3.2 PCH-FW Configuration ME State When Disabled ME will be put into ME Temporarily Disabled Mode. Disabled / Enabled AMT BIOS Features When disabled AMT BIOS Features are no longer supported and user is no longer able to access MEBx Setup. Note: This option does not disable Manageability Features in FW.
  • Page 49 3.3.2.1 Firmware Update Configuration ME FW Image Re-Flash Enable/Disable ME FW Image Re-Flash function. Disabled / Enabled http://www.tyan.com...
  • Page 50 3.3.2.2 PTT Configuration TPM Device Selection Select TPM device: PTT or dTPM. PTT - Enables PTT in SkuMgr dTPM 1.2 – Disables PTT in SkuMgr Warning! PTT/dTPM will be disabled and all data saved on it will be lost. dTPM / PTT http://www.tyan.com...
  • Page 51 3.3.3 Trusted Computing Security Device Support Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. Disabled / Enabled http://www.tyan.com...
  • Page 52 3.3.4 ACPI Settings Enable ACPI Auto Configuration Enables or Disables BIOS ACPI Auto Configuration. Disabled / Enabled Enable Hibernation Enable or Disable System ability to Hibernate (OS/S4 Sleep State). This option may not be effective with some operating system. Disabled / Enabled ACPI Sleep State Select the highest ACPI Sleep state the system will enter when the SUSPEND button is pressed.
  • Page 53 3.3.5 Watchdog Timer Configuration Watchdog Mode The duration of enabling Watchdog Timer. When Watchdog time-out occurs, System will reboot immediately. Disabled / POST / OS / Power ON Watchdog Timer Select 2/4/6/8/10 minutes for Watchdog time intervals. Available when Watchdog Mode is not set to [Disabled].
  • Page 54 3.3.6 NCT6796D Super IO Configuration Serial Port 1 Configuration Set Parameters of Serial Port 1 (COM1). Serial Port 2 Configuration Set Parameters of Serial Port 2 (COM2). http://www.tyan.com...
  • Page 55 3.3.6.1 Serial Port 1 Configuration Serial Port Enable or Disable Serial Port (COM). Disabled / Enabled Device Settings Device Super IO COM1 Address and IRQ. Read only. Change Settings Select an optimal setting for Super IO Device. Auto / IO=3F8h; IRQ=4; / IO=3F8h;...
  • Page 56 3.3.6.2 Serial Port 2 Configuration Serial Port Enable or Disable Serial Port (COM). Disabled / Enabled Device Settings Device Super IO COM2 Address and IRQ. Read only. Change Settings Select an optimal setting for Super IO Device. Auto / IO=2F8h; IRQ=3; / IO=3F8h;...
  • Page 57 3.3.7 Hardware Health Configuration Auto Fan Control Automatic Fan Control. Disabled: Fan speed full on. Enabled: Automatic fan speed control by temperature. Disabled / Enabled PWM Minimal Duty Cycle (suppressed if Auto Fan Control is Disabled) PWM Minimal Duty Cycle. 30% / 45% / 60% http://www.tyan.com...
  • Page 58 3.3.7.1 Sensor Data Register Monitoring Read Only. http://www.tyan.com...
  • Page 59 3.3.8 S5 RTC Wake Settings Wake system from S5 Enable or disable System wake on alarm event. Select Fixed Time, system will wake on the hr:min:sec specified. Disabled / Fixed Time / Dynamic Time Wake system from S5 (available when Wake system from S5 is set to [Fixed time]) Wake up hour Select 0-23.
  • Page 60 Wake system from S5 (available when Wake system from S5 is set to [Dynamic time]) Wake up minute increase Select 1-5. http://www.tyan.com...
  • Page 61 3.3.9 Serial Port Console Redirection Console Redirection Console redirection enable or disable. Disabled / Enabled Legacy Console Redirection Settings Legacy Console redirection settings. Console Redirection EMS Console redirection enable or disable. Disabled / Enabled Console Redirection Settings The settings specify how the host computer (which the user is using) will exchange data.
  • Page 62 3.3.9.1 COM1/COM2/COM3 Console Redirection Settings Terminal Type Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100Plus: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.  VT100 / VT100Plus / VT-UTF8 / ANSI Bits per Second Select serial port transmission speed.
  • Page 63 Stop Bits Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. 1 / 2 Flow Control Flow Control can prevent data loss from buffer overflow.
  • Page 64 3.3.9.2 Legacy Console Redirection Settings Legacy Serial Redirection Port Select a COM port to display redirection of Legacy OS and Legacy OPROM Messages.  COM1 / COM2 / COM3 (Pci Bus0, Dev22, Func3) Resolution On Legacy OS, the Number of Rows and Columns supported redirection. 80x24 / 80x25 Redirect After POST When BootLoader is selected, then Legacy Console Redirection is disabled before...
  • Page 65 3.3.9.3 Serial Port for Out-Of-Band Management/Windows Emergency Services (EMS) Console Redirection EMS Settings Console Redirection EMS [Disabled / Enabled] Out-of-Band Mgmt Port Microsoft Windows Emergency Management Services (EMS) allows for remote management of a Windows Server OS through a serial port. COM1 / COM2 / COM3 (Pci Bus0, Dev22, Func3) Terminal Type VT-UTF8 is the preferred terminal type for out-of-band management.
  • Page 66 Flow Control Flow Control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a ‘stop’ signal can be sent to stop the data flow. Once the buffers are empty, a ‘start’ signal can be sent to restart the flow. Hardware flow control uses two wires to send start/stop signal.
  • Page 67 3.3.10 Option ROM Dispatch Policy Onboard LAN1 OPROM (I219) Enable or disable onboard LAN1 OPROM. Disabled / Enabled Onboard LAN2 OPROM (I225) Enable or disable onboard LAN2 OPROM. Disabled / Enabled PCIE#1~PCIE#3 Empty Enable or Disable Option ROM execution for selected Slot. Enabled / Disabled http://www.tyan.com...
  • Page 68 3.3.11 PCI Subsystem Settings Re-Size BAR Support If system has Resizable BAR capable PCIe Devices, this option Enables or Disables Resizable BAR Support. Enabled / Disabled BME DMA Mitigation Re-enable Bus Master Attribute disabled during Pci enumeration for PCI Bridges after SMM Locked.
  • Page 69 3.3.12 USB Configuration Legacy USB Support Enables USB legacy support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. Disabled / Enabled / Auto XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.
  • Page 70 Device reset time-out USB mass storage device Start Unit command time-out. 10 sec / 20 sec / 30 sec / 40 sec Device power-up delay Maximum time the device will take before it properly reports itself to the Host Controller. ‘AUTO’ uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor.
  • Page 71 3.3.13 Network Stack Configuration Network Stack Enable/Disable UEFI Network Stack. Disabled / Enabled Ipv4 PXE Support (Available when Network Stack Enabled) Enable/Disable Ipv4 PXE Boot Support. If disabled IPV4 PXE boot option will not be created. Disabled / Enabled Ipv4 HTTP Support (Available when Network Stack Enabled) Enable/Disable Ipv4 PXE Boot Support.
  • Page 72 Ipv6 HTTP Support (Available when Network Stack Enabled) Enable/Disable Ipv4 PXE Boot Support. If disabled IPV4 PXE boot option will not be created. Disabled / Enabled PXE boot wait time (Available when Network Stack Enabled) Wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value.
  • Page 73 3.3.14 NVMe Configuration Here shows the Device Name you installed. A sample screenshot shows below.  http://www.tyan.com...
  • Page 74 3.3.15 Onboard Device Configuration LAN1 (T219) Enable or disable onboard LAN1 (I219). Disabled / Enabled LAN2 (T225) Enable or disable onboard LAN2 (I225). Disabled / Enabled Chassis Intrusion Detection Enabled: When a chassis open event is detected, the BIOS will display the event. Disabled / Enabled http://www.tyan.com...
  • Page 75: Chipset Menu

    3.4 Chipset Menu North Bridge System Agent (SA) Parameters. South Bridge PCH Parameters. http://www.tyan.com...
  • Page 76 3.4.1 North Bridge Configuration Memory Configuration Memory Configuration Parameters. Graphics Configuration Graphics Configuration. VMD Setup Menu VMD Configuration settings. http://www.tyan.com...
  • Page 77 3.4.1.1 Memory Configuration Memory Test On Warm Boot Enable or Disable Base memory Test Run on Warm Boot. Enabled / Disabled Maximum Memory Frequency Maximum Memory Frequency Selection in Mhz. Auto / 2666 / 2933 / 3200 http://www.tyan.com...
  • Page 78 3.4.1.2 Graphics Configuration Primary Display Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select HG from Hybrid GFx. Auto / IGFX / PEG Slot / PCH PCIe Internal Graphics Keep IGFX enabled based on the setup option. Auto / Disabled / Enabled http://www.tyan.com...
  • Page 79 3.4.1.3 VMD Setup Menu Enable VMD Controller Enable/Disable to VMD controller. Disabled / Enabled Enable VMD Global Mapping Enable/Disable to VMD Global Mapping. Disabled / Enabled RAID0 Enable/Disable RAID0 support. Disabled / Enabled RAID1 Enable/Disable RAID1 support. Disabled / Enabled RAID5 Enable/Disable RAID5 support.
  • Page 80 RAID10 Enable/Disable RAID10 support. Disabled / Enabled Intel Rapid Recovery Technology Enable/Disable Intel Rapid Recovery Technology. Enabled / Disabled RRT volumes can span internal and eSATA drives Enable/Disable RRT volumes can span internal and eSATA drives. Enabled / Disabled Intel® Optane (TM) Memory Enable/Disable System Acceleration with Intel®...
  • Page 81 3.4.2 South Bridge Configuration SATA Configuration SATA Device Options Settings. HD Audio Configuration HD Audio Subsystem Configuration Settings. DeepSx Power Policies Configure the DeepSx Mode Configuration. Disabled / Enabled in S4-S5 / Enabled in S5 High Precision Time Enable or Disable the High Precision Event Timer. Disabled / Enabled Restore AC Power Loss Specify what state to go to when power is re-applied after a power failure (G3 state).
  • Page 82 3.4.2.1 SATA Configuration SATA Mode Selection Determines how SATA controller(s) operate. AHCI Hot Plug Designates this port as Hot Pluggable. Disabled / Enabled SATA Device Type Identify the SATA port is connected to Solid State Drive or Hard Disk Drive. Hard Disk Drive / Solid State Drive http://www.tyan.com...
  • Page 83 3.4.2.2 HD Audio Configuration HD Audio Control Detection of the HD-Audio device. Disabled = HDA will be unconditionally disabled. Enabled = HDA will be unconditionally enabled. Disabled / Enabled Audio DSP Enable/Disable Audio DSP. Disabled / Enabled http://www.tyan.com...
  • Page 84: Security

    3.4 Security Administrator Password Set Administrator Password. User Password Set User Password. HDD Security Configuration HDD Security Configuration for selected drive. Secure Boot Secure Boot Configuration. http://www.tyan.com...
  • Page 85 3.4.1 Secure Boot Secure Boot Secure Boot feature is Active if Secure Boot is Enabled. Platform Key (PK) is enrolled and the System is in User mode. The mode change requires platform reset. Disabled / Enabled Secure Boot Mode Secure Boot mode options: Standard or Custom. In Custom mode, Secure Boot Policy variables can be configured by a physically present user without full authentication.
  • Page 86 3.4.2.1 Key Management Factory Key Provision Install factory default Secure Boot keys after the platform reset and while the System is in Setup mode. Disabled / Enabled Restore Factory Keys Force System to User Mode. Install factory default Secure Boot key databases. Reset to Setup Mode Deleting all Secure Boot key databases from NVRAM.
  • Page 87 Key Exchange Keys Enroll Factory Defaults or load certificates from a file: 1. Public Key Certificate: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHAXXX 2. Authenticated UEFI Variable 3. EFI PE/COFF Image (SHA256) Key source: Factory, External, Mixed Authorized Signatures Enroll Factory Defaults or load certificates from a file: 1.
  • Page 88 OsRecovery Signatures Enroll Factory Defaults or load certificates from a file: 1. Public Key Certificate: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHAXXX 2. Authenticated UEFI Variable 3. EFI PE/COFF Image (SHA256) Key Source: Factory, External, Mixed Export Secure Boot variables Copy NVRAM content of Secure Boot variables to files in a root folder on a file system device.
  • Page 89: Boot

    3.5 Boot Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting. Bootup NumLock State Select the keyboard NumLock state. On / Off Quiet Boot Enable or disable Quiet Boot option. Disabled / Enabled Wait for ‘ESC’...
  • Page 90 Endless Boot Enabled: BIOS try bootable devices constantly in loop until finding a bootable device (Excluding Built-in EFI Shell). Disabled / Enabled Boot Option #1 ~ Boot Option #2 Sets the system boot order. Device Name / Disabled http://www.tyan.com...
  • Page 91: Save & Exit

    3.6 Save & Exit Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Reset system setup without saving any changes. Restore Defaults Restore/Load Default values for all the setup options. http://www.tyan.com...
  • Page 92: Mailbox

    3.7 MailBox Intel® ME Password MEBx Login. How to setup MEBX password   MEBx default password: admin 1. Enter [admin] at your first MEBX login. Re-configure a new password. Intel® AMT Configuration  Network setup/Intel (R) ME Network Name Settings ...
  • Page 93 Network Access State  Select [Network Active] http://www.tyan.com...
  • Page 94 NOTE http://www.tyan.com...
  • Page 95: Chapter 4: Diagnostics

    Chapter 4: Diagnostics NOTE: if you experience problems with setting up your system, always check the following things in the following order: Memory, Video, CPU By checking these items, you will most likely find out what the problem might have been when setting up your system.
  • Page 96: Amibios Post Code (Aptio)

    4.2 AMIBIOS Post Code (Aptio) The POST code checkpoints are the largest set of checkpoints during the BIOS pre- boot process. The following table describes the type of checkpoints that may occur during the POST portion of the BIOS: Checkpoint Ranges Status Code Range Description 0x01 –...
  • Page 97 SEC Error Codes 0x0C – 0x0D Reserved for future AMI SEC error codes 0x0E Microcode not found 0x0F Microcode not found SEC Beep Codes None PEI Phase Status Code Description Progress Codes 0x10 PEI Core is started 0x11 Pre-memory CPU initialization is started 0x12 Pre-memory CPU initialization (CPU module specific) 0x13...
  • Page 98 Status Code Description 0x38 Post-Memory North Bridge initialization (North Bridge module specific) 0x39 Post-Memory North Bridge initialization (North Bridge module specific) 0x3A Post-Memory North Bridge initialization (North Bridge module specific) 0x3B Post-Memory South Bridge initialization is started 0x3C Post-Memory South Bridge initialization (South Bridge module specific) 0x3D Post-Memory South Bridge initialization (South Bridge module specific) 0x3E...
  • Page 99 Recovery Progress Codes 0xF0 Recovery condition triggered by firmware (Auto recovery) 0xF1 Recovery condition triggered by user (Forced recovery) 0xF2 Recovery process started 0xF3 Recovery firmware image is found 0xF4 Recovery firmware image is loaded 0xF5 – 0xF7 Reserved for future AMI progress codes Recovery Error Codes 0xF8 Recovery PPI is not available...
  • Page 100 Status Code Description 0x6C North Bridge DXE initialization (North Bridge module specific) 0x6D North Bridge DXE initialization (North Bridge module specific) 0x6E North Bridge DXE initialization (North Bridge module specific) 0x6F North Bridge DXE initialization (North Bridge module specific) 0x70 South Bridge DXE initialization is started 0x71 South Bridge DXE SMM initialization is started...
  • Page 101 Status Code Description 0xA5 SCSI Reset 0xA6 SCSI Detect 0xA7 SCSI Enable 0xA8 Setup Verifying Password 0xA9 Start of Setup 0xAA Reserved for ASL (see ASL Status Codes section below) 0xAB Setup Input Wait 0xAC Reserved for ASL (see ASL Status Codes section below) 0xAD Ready To Boot event 0xAE...
  • Page 102 DXE Beep Codes # of Beeps Description Invalid password Some of the Architectural Protocols are not available No Console Output Devices are found No Console Input Devices are found Flash update is failed Reset protocol is not available Platform PCI resource requirements cannot be met ACPI/ASL Checkpoints Status Code Description...
  • Page 103: Appendix I: How To Recover Uefi Bios

    Appendix I: How to recover UEFI BIOS BIOS Recovery Process Recovery is a BIOS function that allows the user to update or change the BIOS programmed into a flash part. In order to keep recovery function workable, the BIOS must have the Boot Block section of the BIOS in a non-corrupted state. Recovery can be invoked by pressing hot key from PS2 keyboard and USB keyboard in early POST.
  • Page 104 If recovery is triggered, system will enter recovery screen as shown below. Move the cursor to the Proceed with flash update submenu, press Enter to continue. http://www.tyan.com...
  • Page 105 It takes a few minutes to update the main firmware. A sample screenshot is shown below. http://www.tyan.com...
  • Page 106 If no recovery file is found, a “ROM Image is not loaded. ROM Image update denied.” message will display on the screen. http://www.tyan.com...
  • Page 107: Appendix Ii: Fan And Temp Sensors

    Appendix II: Fan and Temp Sensors This section aims to help readers identify the locations of some specific FAN and Temp Sensors on the motherboard. A table of BIOS Temp sensor name explanation is also included for readers’ reference. Figure 1: Sensor Location NOTE: The red mark indicates the sensor.
  • Page 108 BIOS Temp Sensor Name Explanation: BIOS Temp Sensor Name Explanation P0_Temp Temperature of the CPU0 P0_DTS_Margin Temperature of the CPU0 Digital Temperature Sensor PCH_Temp Temperature of PCH P0_MOS_Area_1 Temperature of the CPU0 MOS Area 1 P0_MOS_Area_2 Temperature of the CPU0 MOS Area 2 M.2_NVME_Area Temperature of the M.2 NVME Area P0_CHA_DIM0...
  • Page 109: Glossary

    Glossary ACPI (Advanced Configuration and Power Interface): a power management specification that allows the operating system to control the amount of power distributed to the computer’s devices. Devices not in use can be turned off, reducing unnecessary power expenditure. AGP (Accelerated Graphics Port): a PCI-based interface which was designed specifically for demands of 3D graphics applications.
  • Page 110 Bus: a data pathway. The term is used especially to refer to the connection between the processor and system memory, and between the processor and PCI or ISA local buses. Bus mastering: allows peripheral devices and IDEs to access the system memory without going through the CPU (similar to DMA channels).
  • Page 111 DRAM (Dynamic RAM): widely available, very affordable form of RAM which looses data if it is not recharged regularly (every few milliseconds). This refresh requirement makes DRAM three to ten times slower than non-recharged RAM such as SRAM. ECC (Error Correction Code or Error Checking and Correcting): allows data to be checked for errors during run-time.
  • Page 112 I/O (Input/Output): the connection between your computer and another piece of hardware (mouse, keyboard, etc.) IRQ (Interrupt Request): an electronic request that runs from a hardware device to the CPU. The interrupt controller assigns priorities to incoming requests and delivers them to the CPU. It is important that there is only one device hooked up to each IRQ line;...
  • Page 113 RAID (Redundant Array of Independent Disks): a way for the same data to be stored in different places on many hard drives. By using this method, the data is stored redundantly and multiple hard drives will appear as a single drive to the operating system.
  • Page 114 Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally. UltraDMA-33/66/100: a fast version of the old DMA channel. UltraDMA is also called UltraATA. Without a proper UltraDMA controller, your system cannot take advantage of higher data transfer rates of the new UltraDMA/UltraATA hard drives.
  • Page 115: Technical Support

    Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains.
  • Page 116 NOTE: A receipt or copy of your invoice marked with the date of purchase is required before any warranty service can be rendered. You may obtain service by calling the manufacturer for a Return Merchandise Authorization (RMA) number. The RMA number Should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid.

Table of Contents