Table of Contents
Advertisement
[Auto setting]
Set whether to make the IP setting for IPv6
automatically.
[On]: Obtain the IP address automatically.
[Off]: Sets the IP address manually.
[Temporary address]
With [Auto setting] set to [On], set whether to use the
temporary IP address.
[On]: Uses the temporary address.
[Off]: Does not use the temporary address.
[IP address]
(IPv6 address display and setting)
With [Auto setting] set to [Off], enter the IP address.
[Prefix length]
With [Auto setting] set to [Off], set the prefix length
(netmask).
[Gateway]
(Gateway address display and setting)
With [Auto setting] set to [Off], enter the Gateway
address.
Note
●
Initial values for [IP address] and [Gateway] for
[IPv6 settings] are blank.
●
When [Auto setting] is set to [On], the IP address,
etc. will be displayed in gray.
Entering numbers
When IPv6 address is set
•
IP address
1
2
3
a
4
5
6
c
7
8
9
e
:
0
Delete
1. Select the address to be set, and press <ENTER>.
2. Press
to select the numbers to be set,
and press <ENTER>.
3. Select [Ok] and press <ENTER>.
Select [Save] and press <ENTER>.
The current network settings are saved.
[Command port]
Set the port number used for command control.
Select [Command port] and press <ENTER> to set
the number.
The available setting range is 1024 ‒ 65535.
•
Entering numbers (see page 82)
•
Note
●
When the PJLink protocol is used, the port setting
is not necessary.
b
d
f
All delete
Ok
[EAP]
Select the EAP that has been set for the RADIUS
server. If the EAP has not been set, select [None].
The types of EAPs that can be set are as follows.
[PEAP(MS-CHAPv2)], [PEAP(GTC)], [EAP-
TTLS(MD5)], [EAP-TTLS(MS-CHAPv2)], [EAP-
FAST(MS-CHAPv2)], [EAP-FAST(GTC)], [EAP-TLS]
[User name]
Enter the user name for authentication with one-byte
alphanumeric characters (excluding space). (Up to 64
characters)
This can be set only when [EAP] is set to items other
than [None] or [EAP-TLS].
[Password]
Enter the password for authentication with one-byte
alphanumeric characters. (Up to 64 characters)
This can be set only when [EAP] is set to items other
than [None] or [EAP-TLS].
Note
●
When EAP is used, this unit needs to be
configured according to the settings of the RADIUS
server.
For the settings of the RADIUS server, consult with
the network administrator.
●
When [EAP] is set to [EAP-TLS], set [Date and
time] (see page 77) and register the certificate on
the WEB browser control. (see page 109)
[MAC address]
Displays the MAC address of this unit.
■
[Network status]
Lower than Version 1.5000 (before IPv6
compatible)
Checks the current Network settings status.
The screen configuration of this menu screen differs
before and after IPv6 compatible.
Network status
DHCP
IP address
192. 168. 0. 8
Subnet mask
255. 255. 255. 0
Gateway
192. 168. 0. 1
EAP
MAC address
12:34:56:78:9A:BC
■
[Network status (IPv4)]
Version 1.5000 and later (after IPv6 compatible)
Network status (IPv4)
DHCP
IP address
192. 168. 0. 8
Subnet mask
255. 255. 255. 0
Gateway
192. 168. 0. 1
EAP
MAC address
12:34:56:78:9A:BC
Off
None
Off
None
English
83
Advertisement
Table of Contents
