Table of Contents
Advertisement
pickering
Specifications
Relay Type
The 40-597 BRIC modules are fitted with electro-mechanical relays
(Palladium-Ruthenium, Gold Covered Bifurcated).
Switching Specification
Relay Type:
Contact Type:
Max Switch Voltage:
Max Power:
Max Switch Current:
Max Continuous Carry Current:
Max Pulsed Carry Current
Example (for a single switch path):
Initial On Path Resistance:
Off Path Resistance:
Thermal Offset:
Max Number of Simultaneously
Closed Crosspoints:
Switch Operate Time:
Expected Life (operations)
Very low power signal load:
Low power load (2W):
Medium power load (30W):
Full power load (60W):
* For full voltage rating, signal sources to be switched must be fully
isolated from mains supply and safety earth.
Typical Bandwidth and Crosstalk
Bandwidth (-3dB):
Crosstalk (typical):
Isolation:
Matrix Functionality
Permits any X to X with multiple connections and 12 concurrent Y
paths. Direct Y connections are not provided at the user connector
but can be accessed by reassignment of 12 off X connections to
provide Y connections. The driver prevents the connection of Y
axis connections together (e.g. Y1 to Y4).
Power Requirements - BRIC2 & BRIC4
+3.3V
+5V
50mA
1.5A
2A Electro-mechanical
Relay
Palladium-Ruthenium, Gold
Covered Bifurcated
100VDC/70VAC*
62.5VA, 60W
2A
2A
6A for 100ms
(up to 10% duty cycle)
<1Ω
>10
Ω
9
10µV (X to X connection)
BRIC2 & BRIC4: 65
BRIC8: 130
6.5ms
>1x10
8
>1.5x10
(0.1A 20VDC)
7
>5x10
(1A 30VDC)
6
>1x10
(2A 30VDC)
5
>5MHz
10kHz:
-70dB
100kHz:
-55dB
1MHz:
-35dB
10MHz:
-20dB
10kHz:
75dB
100kHz:
60dB
1MHz:
40dB
10MHz:
20dB
+12V
-12V
35mA
0
1-POLE 2A BRIC 3U PXI MULTI-SLOT MATRIX 40-597
SECTION 1 - TECHNICAL SPECIFICATION
1-Pole 2 Amp BRIC Matrix – 40-597
Power Requirements - BRIC8
+3.3V
+5V
115mA
2.2A
Width and Dimensions
Two, four or eight slot 3U PXI module (CompactPCI).
3D models for these modules in a variety of popular file formats are
available on request.
Module Weight
Empty BRIC
BRIC2
0.6Kg
BRIC4
0.9Kg
BRIC8
1.6Kg
BRIC daughter card
Connectors
PXI bus via 32-bit P1/J1 backplane connector.
Signals via multiple front panel 37-pin male D-type connectors (Up
to 4 per 4-slot module or up to 8 per 8-slot module), for pin outs
please refer to the operating manual.
Special Versions
BRIC modules can be built in special versions, for example
where an exact matrix size is required then partly populated
daughtercards may be ordered.
Upgrading With Daughtercards
BRIC modules can be upgraded to larger matrix sizes using
daughter-cards, please consult your local sales office for further
information.
Operating/Storage Conditions
Operating Conditions
Operating Temperature:
Humidity:
Altitude:
Storage and Transport Conditions
Storage Temperature:
Humidity:
Altitude:
PXI & CompactPCI Compliance
The module is compliant with the PXI Specification 2.2. Local Bus,
Trigger Bus and Star Trigger are not implemented.
Uses a 33MHz 32-bit backplane interface.
Safety & CE Compliance
All modules are fully CE compliant and meet applicable EU
directives: Low-voltage safety EN61010-1:2010, EMC Immunity
EN61326-1:2013, Emissions EN55011:2009+A1:2010.
+12V
-12V
35mA
0
Fully Loaded BRIC
1.3Kg
2.2Kg
4.2Kg
325g
0°C to +55°C
Up to 90% non-condensing
5000m
-20°C to +75°C
Up to 90% non-condensing
15000m
pickeringtest.com
Page 1.3
Advertisement
Table of Contents
