Table of Contents
Advertisement
B. Old Work / Remodel Flush Mounting (Using an recommended Carlon BH234R
Rough-In Box)
Recommended mounting heighy to bottom of the rough-in box is 50" - 54". Make sure mounting
Step 1
location is free of wall studs, wires, etc..
Place Rough-In box LEVEL against siding. Trace outline of box onto siding. Note: A siding mounting
Step 2
block is recommended when mounting to vinyl siding or siding with a 4 inch or less horizontal lap.
Contact siding installer for the correct mounting block.
Cut a hole through the siding and wall sheathing just large enough for the rough-in box. Caution:
Step 3
Too large of a hole can cause plate misalignment and compromise the gasket seal.
The front surface of the Rough-In box can be mounted flush against wood siding or can be recessed
Step 4
and mounted flush against wall sheathing when mounting on aluminum, steel or vinyl siding.
When mounting to 5/8 inch thick or less wall sheathing the two attached screws with wing brackets
can be used to secure the rough-in box. When mounting to surfaces thicker than 5/8 inch, four
Step 5
standard flat head dry wall screws can be used to secure the Rough-In box through its mounting
ears. (See page 4 Section D.)
To maintain a vapor barrier on outside wall applications, caulk around the box, filling any gaps
Step 6
between the box and the rough opening. Apply caulk to any holes in the box around wires, etc.
C. Surface Mounting
A Viking model VE-5x5 can be used to surface mount an E-75 to a wall or post. ecommended mounting heighy
to bottom of the rough-in box is 50" - 54". Drill a small wire exit hole in wall. Pull wire through and seal hole around
wire with putty or caulking. Route wire into the VE-5x5 box, securely screw it to wall or post and seal hole in box
around wire with putty or caulking. Note: Conduit may also be used when surface mounting wire, but should not
enter through the top of the VE-5x5. When routing wiring from above, a drip loop is required. WARNING: Do NOT
use a typical "wet location box" as not all styles seal properly with the E-75 faceplate.
D. Mounting the Faceplate
After the Rough-In box or VE-5x5 is securely mounted, caulking between the box and rough opening is completed
(if required), and wires are connected, remove paper liner from face plate gasket back and place it on back side
of the faceplate aligning with push button hole. Push the 1-1/4" 6-32 screws through faceplate holes and small
holes in gasket, the faceplate gasket should retain the screws. Position Circuit board mounting plate over screws.
Align screws with double gang box bosses and tighten face plate until gasket is fully collapsed and the push
button is protruding through the clearance hole in the face plate. Included 1/4" thick gasket will provide an adequate
seal for most siding surfaces; however for rough surfaces (ie: brick, stucco, etc.) additional caulking may be
required.
Wing Brackets
Belden
9537
Cable
*2.25"
Deep
Min.
"Old Work" Double Gang Rough-In
Box with minimum dimensions of:
3.65"W x 2.84"H x 2.25"D. (Carlon BH234R box shown, not included)
-OR-
5.22"
5.14"
2.25"
Optional VE-5x5 Surface Mount Box with Black Satin Powder Paint Finish, not included (DOD 424)
4
(9) 3-Wire Gel-Filled
Butt Connectors
(included)
Wires from
Phone Board
W/BL
CAT5E
Green
Cable
Blue
Red
Wires from
Orange
Camera
Red
W/O
Black
Green
W/G
Yellow
Wires from
Proximity Card
Black
Reader
Black
Red
Red
Green
Green
White
White
3.25"
(2) Junction Box to
Double Gang Adapter
Plates and (4) 5/64 Hex
Drive Flat Head Screws
(included with the E-75)
3.63"
3.63"
WARNING: Do NOT use a wet location box.
Circuit Board
1/4" Thick Foam
Mounting Plate
Faceplate Gasket
(included)
(included)
** Important: Push LED light pipe into faceplate
hole, then place faceplate upside down on a clean
flat surface and push down on back side of plate
until light pipe is fully seated and straight.
WARNING: Inserting the light pipe more than one
time can cause a loose fit
* CAUTION: Excessive wire length and/or using a
rough-in box with inadequate depth can apply force
to the circuit board causing physical damage.
** LED
Light Pipe
(included)
(4) 6-32 x 1.25" Long
5/64" Hexdrive
Facplate
Flathead Screws
(included)
(included)
.
Advertisement
Table of Contents
