Table of Contents
Advertisement
Final Installation Checklist
Final Installation Checklist
•
Inspect and ensure that all components and
accessories have been installed properly and
Inspect and ensure that all components and
that they have not been damaged during the
accessories have been installed properly and
installation process.
that they have not been damaged during the
•
Ensure that all installation instructions
installation process.
concerning clearances around the unit have been
Ensure that all installation instructions
adhered to.
•
concerning clearances around the unit have
Check to ensure that the unit air filter, indoor
coil, and outdoor coil are free from any
been adhered to.
obstructions.
Check to ensure that the unit air filter, indoor
•
Ensure that the circuit breaker(s) or fuse(s) and
coil, and outdoor coil are free from any
supply circuit wire size have been sized correctly.
obstructions.
•
Check the condensate water drain(s) to ensure
Ensure that the circuit breaker(s) or fuse(s)
that they are adequate for the removal of
and supply circuit wire size have been sized
condensate water and that they meet approval of
correctly.
the end user.
•
Check the condensate water drain(s) to
Ensure that the entire installation is in
compliance with all applicable national and local
ensure that they are adequate for the
codes and ordinances having jurisdiction.
removal of condensate water and that they
•
ENSURE THAT THE SUPPLY VOLTAGE TO THE
meet approval of the end user.
UNIT IS WITHIN THE OPERATING RANGE
Ensure that the entire installation is in
•
Secure all access panels (i.e. front cover and/or
compliance with all applicable national and
control box), apply power to the unit.
local codes and ordinances having
The unit commissioning should be done at this
jurisdiction.
time to ensure unit function.
Secure all access panels (i.e. front cover
NOTE: Maintaining a log for recording the dates
and/or control box), apply power to the unit
of maintenance and/or service is recommended,
The unit commissioning should be done at
and should be suggested to the owner or
operator of the equipment.
this time to ensure unit function.
•
Present the owner or operator of the equipment
NOTE: Maintaining a log for recording the dates
with the Installation & Operation Manual, all
of maintenance and/or service is recommended,
accessory installation instructions, and the name,
and should be suggested to the owner or
address and telephone number of the Authorized
operator of the equipment.
Friedrich Warranty Service Company in the area
for future reference if necessary.
Present the owner or operator of the
WARNING: Do not operate the unit during
equipment with the Installation & Operation
construction. Doing so can damage the
Manual, all accessory installation
equipment and void warranty.
instructions, and the name, address and
telephone number of the Authorized Friedrich
Warranty Service Company in the area for
future reference if necessary.
Chassis Operation
Chassis Operation
Cooling Operation
Cooling Operation
The set point must be at least 3°F below room
temperature to ensure compressor operation.
The set point must be at least 3°F below room
In the cooling mode, when demand is present, the
temperature to ensure compressor operation.
indoor blower and outdoor fan will operate. The
In the cooling mode, when demand is present, the
compressor will vary operating speed to maintain
indoor blower and outdoor fan will operate. The
desired set point.
compressor will vary operating speed to maintain
desired set point.
Heat Pump Operation
Heat Pump Operation
The set point must be greater than 3°F but not
greater than 6°F above room temperature to
The set point must be greater than 3°F but not
ensure compressor operation.
In the heating mode, when demand is present, the
greater than 6°F above room temperature to ensure
indoor blower and outdoor fan will operate. The
compressor operation.
compressor will vary operating speed to maintain
In the heating mode, when demand is present, the
desired set point.
indoor blower and outdoor fan will operate. The
compressor will vary operating speed to maintain
desired set point.
Electric Heat Operation
If the set-point is greater than 5°F - 15°F
(depending on outdoor conditions) above room
Electric Heat Operation
temperature, the heat pump operation will
be terminated and the electric heater will be
If the set-point is greater than 6°F above room
energized to satisfy the heating demand.
temperature, the heat pump operation will be
If heat pump operation is not available due to
defrost or error, the electric heater will be used to
terminated and the electric heater will be energized
satisfy heating demand.
to satisfy the heating demand.
If heat pump operation is not available due to
FreshAire™
defrost or error, the electric heater will be used to
satisfy heating demand.
The FreshAire™ System (optional) delivers outside
air to the indoor space. The system has a fan that
draws outdoor air into the system. The outdoor air
FreshAire™
leaves the system through a filter and enters the
indoor space in front of the indoor conditioning
The FreshAire™ System (optional) delivers outside
coil. The outdoor air mixes with the return air and
air to the indoor space. The module has a fan that
is drawn through the indoor conditioning coil. The
draws outdoor air into the module. The outdoor air
optional system can be configured to have either a
single (F option) outdoor air fan and filter, or dual
leaves the module through a filter and enters the
(D option) outdoor air fans and filters.
indoor space in front of the indoor conditioning coil.
The outdoor air mixes with the return air and is
The FreshAire™ System uses one 6 x 6 x 1 filter.
drawn through the indoor conditioning coil. The
The filter is accessed through the front of the
optional module can be configured as either a single
unit just below the main unit filter. Slide the filter
(F option) or a dual (D
straight out to remove and straight in to replace.
option)..
32
Advertisement
Table of Contents
