Unigas G258A Manual Of Installation - Use - Maintenance page 125

InP
sp. r
0
Def. remote setpoint
typ.
30
Probe type, signal, enable custom linearization,
Type Probe type
Sensore:
0 TC J °C
1 TC J °F
2 TC K °C
3 TC K °F
4 TC R °C
5 TC R °F
6 TC S °C
7 TC S ° F
8 TC T °C
9 TC T °F
28
29
30 PT100 °C
31 PT100 °F
32 JPT100 °C
33 JPT100 °F
34 PTC °C
35 PTC °F
36 NTC °C
37 NTC °F
38 0...60 mV
39 0...60 mV
40 12...60 mV
41 12...60 mV
42 0...20 mA
43 0...20 mA
44 4...20 mA
45 4...20 mA
46 0...10 V
47 0...10 V
48 2...10 V
49 2...10 V
50 0...5 V
51 0...5 V
52 1...5 V
53 1...5 V
54 0...1 V
55 0...1 V
56 200mv..1V
57 200mv..1V
58 Cust10 V-20mA
59 Cust10 V-20mA
60 Cust 60mV
61 Cust 60mV
62 PT100-JPT
63
64
For custom linearization:
- LO signal is generated with variable below Lo.S or at minimum calibration
value
- HI signal is generated with variable above Lo.S or at maximum calibration
value
80379_MHW_600V-T73_06-2012_ENG
• InP
Input settings
0 default (remote setpoint present)
+2 Times of pre-heating and gradients of set digit/sec
and main input scale
without decimal point with decimal point
TC
0/1000 0.0/999.9
32/1832 32.0/999.9
0/1300 0.0/999.9
32/2372 32.0/999.9
0/1750 0.0/999.9
32/3182 32.0/999.9
0/1750 0.0/999.9
32/3182 32.0/999.9
-200/400 -199.9/400.0
-328/752 -199.9/752.0
TC CUSTOM CUSTOM
TC CUSTOM CUSTOM
-200/850 -199.9/850.0
-328/156 2 -199.9/999.9
-200/600 -199.9/600.0
-328/1112 -199.9/999.9
-55/120 -55.0/120.0
-67/248 -67.0/248.0
-10/70 -10.0/70.0
14/158 14.0/158.0
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
-1999/9999 -199.9/999.9
Custom scale Custom scale
CUSTOM CUSTOM
PTC CUSTOM CUSTOM
NTC CUSTOM CUSTOM
S, R range 0...1750°C; error < 0.2% f.s. (t > 300°C) / for other
T
B
U
Max. non-linearity error for
thermocouples (TC),
resistors (PT100) and
G
thermistors (PTC, NTC).
D
C
The error is calculated as
deviation from theoretical
value and is expressed as
percentage of full scale
NTC error < 0.5% f.s.
(in °C).
Tc: J, K, E, N, L
JPT100 and PTC
PT100 scale -200...850°C
flt
0.1
(if = 0 excludes averaging filter on
fld
0.5
Digital filter on input
dp. s
1
Decimal point position for
Minimum limit of main
lo. s
0.0
850.0
Maximum limit of main
xi. s
0
Offset correction
ofs.
of main input
Lower limit for setting SP
lo. l
30.0
and absolute alarms
Upper limit for setting SP
xi. l
130.0
and absolute alarms
range; error < 0.5% f.s.
error < 0.2% f.s. (t > -150°C)
range 44...1800°C; error < 0.5% f.s. (t > 300°C) / range
44,0...999,9; error < 1% f.s. (t > 300°C)
range -99,9...99,9 and -99...99°C; error < 0.5% f.s. / for other
range; error < 0.2% f.s. (t > -150°C)
error < 0.2% f.s. (t > 300°C)
error < 0.2% f.s. (t > 200°C)
range 0...2300; error < 0.2% f.s. / for other range;
error < 0.5% f.s.
error < 0,2% f.s.
error < 0,2% f.s.
Precision better than 0,2% f.s. at 25°C
In range 0...50°C:
• Precision better than 0,2% f.s. in range -200...400°C
• Precision better than 0,4% f.s. in range +400...850°C
(where f.s. refers to range -200... +850°C)
Digital filter on input
0.0 ... 20.0 sec
sample value)
0 ... 9.9
display scale points
dP_S Format
0 xxxx
1 xxx.x
input scale
2 xx.xx (*)
3 x.xxx (*)
(*) not available for TC, RTD,
PTC and NTC scales
min...max input range
input scale selected in tyP
min...max input range
input scale selected in tyP
-999 ... 999
scale points
Lo.S ... Hi.S
Lo.S ... Hi.S
5