Roland VS-2400CD Appendices page 98

Algorithm List
HiMid Q (High Middle Q)
High Gain (High Gain)
High Freq (High Frequency)
High Q (High Q)
Hi Type (High Type)
Level (Level)
BCut (Bass Cut Filter):
Sw (Switch)
Freq (Frequency)
Enh (Enhancer):
Sw (Switch)
Sens (Sensitivity)
Freq (Frequency)
MixLvl (Mix Level)
In (Input):
InGain (Input Gain)
D-Time (Detect Time)
Split Point Low (Low Split Point) 20–800 Hz
Split Point High (High Split Point) 1.60–16.0 kHz
Exp (Expander):
Sw (Switch)
Low Thre (Low Threshold)
Low Ratio (Low Raito)
Low Atck (Low Attack)
Low Rel (Low Release)
Mid Thre (Middle Threshold)
Mid Ratio (Middle Ratio)
Mid Atck (Middle Attack)
Mid Rel (Middle Release)
High Thre (High Threshold)
High Ratio (High Ratio)
High Atck (High Attack)
High Rel (High Release)
98
0.3–16.0
-12– +12 dB
1.40–20.0 kHz
0.3–16.0
Shlv, Peak
-24– +12 dB
Cuts off undesired low frequency band sounds such as pop noise.
On, Off
Thru, 20 - 2000 Hz
Accentuates the sound and push the sound forward.
On, Off Turns the enhancer on or off.
0–100 Sets the degree of the enhancer effect desired.
1.00–10.0 kHz Sets the frequency at which the enhancer effect starts working.
-24– +12dB Set the amount of the enhancer sound to be added to the direct sound.
Splits the direct sound into three frequency bands, that is, low, middle and High
frequency bands.
-24– +12dB Sets the overall volume before entering expander/compressor.
0–10 ms Sets the length of delay to add to the direct sound input.
Sets the frequency at which the direct sound is split into three bands (on the
low frequency band side).
Sets the frequency at which the direct sound is split into three bands (on the
High frequency band side).
Expands the dynamic range at a certain ratio.
On, Off Turns the expander on or off.
-80–0 dB Sets the volume at which the expander for the low frequency band starts working .
1:1.0–1:16, 1:INF Sets the ratio at which the output in the low frequency band is increased
when the input level has exceeded below the low threshold level.
0–100 ms Sets the time until when the low frequency band expander starts working
after the input level dropps below the low threshold level.
50 ms–5.000 s Sets the time until when the High frequency band expander stops working
after the input level exceeds the low threshold level.
-80–0 dB Sets the volume at which the expander for the middle frequency band starts
working .
1:1.0–1:16, 1:INF Sets the ratio at which the output in the middle frequency band is increased
when the input level has exceeded below the middle threshold level.
0–100 ms Sets the time until when the middle frequency band expander starts working
after the input level dropps below the middle threshold level.
50 ms–5.000 s Sets the time until when the middle frequency band expander stops working
after the input level exceeds the middle threshold level.
-80–0 dB Sets the volume at which the expander for the High frequency band starts
working .
1:1.0–1:16, 1:INF Sets the ratio at which the output in the High frequency band is increased
when the input level has exceeded below the High threshold level.
0–100 ms Sets the time until when the High frequency band expander starts working
after the input level dropps below the High threshold level.
50 ms–5.000 s Sets the time until when the High frequency band expander stops working
after the input level exceeds the High threshold level.
Sets the width of the area around the High middle
frequency that will be affected by the gain settings.
Sets the boost/cut amount in the High frequency band.
Sets the center frequency in the High frequency band.
Sets the width of the area around the High frequency that
will be affected by the gain settings.
Sets the type of the High frequency band equalizer (Shlving
type or peaking type).
Sets the overall volume after passing through the equalizer.
Turns the bass cut filter on or off.
Sets the frequency for cutting off undesired low frequency
band sounds such as pop noise.
*1