Roland VS-2400CD Appendices page 75

Parameter (full name)
Comp (Compressor):Compresses the entire output signals when the input volume exceeds a specified value.
Sw (Switch)
Sustain (Sustain)
Attack (Attack)
Tone (Tone)
Level (Level)
Metal (Heavy Metal) / Dstr (Distortion) / Ovd (Overdrive): Gives distortion to the sound.
Sw (Switch)
Gain (Gain)
Low Gainain (Low Gain)
MidGain (Middle Gain)
High Gainain (High Gain)
Tone (Tone)
Level (Level)
NS (Noise Suppressor):
Sw (Switch)
Thresh (Threshold)
Release (Release)
Wah (Auto Wah):
Sw (Switch)
Mode (Mode)
Pol (Polarity)
Sens (Sense)
Freq (Frequency)
Peak (Peak)
Rate (Rate)
Depth (Depth)
Level (Level)
Mdl (Guitar Amplifier Simulator): Models Guitar Amplifier.
Sw (Switch)
Mode (Mode)
Flg (Flanger):
Sw (Switch)
Rate (Rate)
Depth (Depth)
Manual (Manual)
Reso (Resonance)
Setting
On, Off
0–100
0–100
-50–50
0–100
On, Off
0–100
-100–100
-100–100
-100–100
0–100
0–100
Mutes noise in the silent mode.
On, Off
0–100
0–100
Adds the wah effect.
On, Off
LPF, BPF
Up, Down
0–100
0–100
0–100
0.1–10.0 Hz
0–100
0–100
On, Off
See the column on
the previous page.
Adds effects similar to ascending/descending sound of a jet.
On, Off
0.1–10.0 Hz
0–100
0–100
0–100
Function
Turns the compressor on or off.
Sets the time over which low level signals are boosted to a
constant volume.
Sets the strength of attack when a sound is input.
Sets the tone color.
Sets the volume of the compressor sound.
Turns the metal, distortion or overdrive on or off.
Sets the degree of the distortion.
Sets the boost/cut amount in the low frequency band. (only for Metal)
Sets the boost/cut amount in the middle frequency band.(only for Metal)
Sets the boost/cut amount in the High frequency band. (only for Metal)
Sets the tone color. (for Distortion/Overdrive only)
Sets the volume of the metal, distortion or overdrive sound.
Turns the noise suppressor on or off.
Sets the level to start muting noise.
Sets the time over which the volume will drop to 0 after the noise
starts being muted.
Turns the auto wah on or off.
Set to "BPF" for the wah effect in a narrow range of frequencies
and to "LPF" for wah effect in a broad range of frequencies.
Activated only for adding the wah effect according to input volume
changes. Set to "Up" for moving the filter to a Higher frequency and
"Down" for moving it to a lower frequency.
Normally "0."
Sets sensitivity for input volume changes for adding the wah effect
according to input volume changes.
Sets the frequency at which the wah effect starts working.
Sets the degree of the wah effect applied at around the frequency.
Sets the rate at which the wah effect will be cyclically modulated.
Sets the depth at which the wah effect will be cyclically modulated.
Sets the volume of the wah sound.
Turns the guitar amplifier simulator on or off.
Type of the guitar amplifier.
Turns the flanger on or off.
Sets the rate of modulation for the flanger.
Sets the depth of modulation for the flanger.
Sets the center frequency subject to application of the flanger effect.
Enhances frequency components at around the center frequency
set with Manual.
Algorithm List
Continued...
75