Roland VS-2000 Appendices page 97

4. Bulk Dump
VS-2000 can transfer and receive the scenes, the EZ ROUTING User Templates and the User
Effect Patches by bulk dump.
In order to make bulk dump transmit, a transmitting function is performed on UTILITY-
MIDI BULK DUMP screen.
In order to make bulk dump receive, after changing into a reception standby state on
UTILITY-MIDI BULK DUMP screen, the bulk dump which the VS-2000 outputted
beforehand is sent to the VS-2000.
■ Address Block
+—————————————————————————————————————————————————————————————————+
| Start |
| address | Contents and remarks
|=============+===================================================|
| 10 00 00 00 | SCENE #1—1
: :
| 10 00 7F 7F |
|—————————————+———————————————————————————————————————————————————|
| 10 01 00 00 | SCENE #1—2
: :
| 10 01 7F 7F |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 10 0F 00 00 | SCENE #1—16
: :
| 10 0F 7F 7F |
|—————————————+———————————————————————————————————————————————————|
| 10 10 00 00 | SCENE #2—1
: :
| 10 10 7F 7F |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 10 5F 00 00 | SCENE #6—16
: :
| 10 5F 7F 7F |
|—————————————+———————————————————————————————————————————————————|
| 11 00 00 00 | EZ ROUTING USER TEMPLATE #00
: :
| 11 00 7F 7F |
|—————————————+———————————————————————————————————————————————————|
| 11 01 00 00 | EZ ROUTING USER TEMPLATE #01
: :
| 11 01 7F 7F |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 11 13 00 00 | EZ ROUTING USER TEMPLATE #19
: :
| 11 13 7F 7F |
|—————————————+———————————————————————————————————————————————————|
| 12 00 00 00 | EFFECT USER PATCH #000
: :
| 12 00 01 7F |
|—————————————+———————————————————————————————————————————————————|
| 12 00 02 00 | EFFECT USER PATCH #001
: :
| 12 00 03 7F |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 12 03 0E 00 | EFFECT USER PATCH #199
: :
| 12 03 0F 7F |
+—————————————————————————————————————————————————————————————————+
5. V-LINK TRANSMITTED DATA
The following control command will be transmitted while V-LIN function is activated.
■ CHANNEL VOICE MESSAGES
● CONTROL CHANG
❍Controller Number 0
This is used to switch image banks. (MIDI ch.=1 fixed)
In the V-LINK activated mode, while AUTOMIX is playing, this is transmitted when the
current time coincides with the pre-registered time for switching image bank.
Status Second
|
| B0H 00H
|
mm = Bank Nunber : 00H - 7FH (1 - 128)
|
❍Controller Number 1
|
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
|
is also On, this message is transmitted when you operate a fader assigned to Brightness
(MIDI ch. is fixed at 1).
|
Status Second
|
B0H 01H
|
|
mm = Control Value: 0H - 7FH (0 - 127)
❍Controller Number 5
|
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
|
is also On, this message is transmitted when you operate a fader assigned to Dissolve Time
(MIDI ch. is fixed at 1).
|
|
Status Second
|
B0H 05H
|
mm = Control Value : 0H - 7FH (0 - 127)
|
❍Controller Number 7
|
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Color Cb
|
(MIDI ch. is fixed at 1).
|
| Status Second
B0H 07H
|
mm = Control Value : 0H - 7FH (0 - 127)
|
❍Controller Number 10
|
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Color Cr (MIDI
ch. is fixed at 1).
Status Second
B0H 0AH
mm = Control Value : 0H - 7FH (0 - 127)
❍Controller Number 11
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to T Bar (MIDI ch.
is fixed at 1).
Status Second
B0H 0BH
mm = Control Value : 0H - 7FH (0 - 127)
❍Controller Number 72
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Playback
Speed (MIDI ch. is fixed at 1).
Status Second
B0H 48H
mm = Control Value : 0H - 7FH (0 - 127)
Third
mmH
Third
mmH
Third
mmH
Third
mmH
Third
mmH
Third
mmH
Third
mmH
97