Roland VS-2000 Appendices page 25

Gate Reverb
This is a reverb in which the reverberation is muted during its decay. Its reverse mode can be used in conjunction with Accent
sounds to obtain sounds like from reverse play back of a tape.
fig.08-42
Input L
Input R
Gate Reverb
fig.08-43e
Level
Direct sound (DirLvl)
Reverb sound
Gate Time
(Time)
Pre Delay
(PreDLY)
Parameter (full name)
GRev (Gate Reverb):
Sw (Switch)
Mode (Gate Mode)
Time (Gate Time)
PreDLY (Pre-Delay)
Thick (Thickness)
Densty (Density)
AcDLY (Accent Delay Time)
AcLvl (Accent Level)
AcPan (Accent Pan)
FX Lvl (Effect Level).
DirLvl (Direct Level)
EQ (Equalizer)
Sw (Switch)
Low Gain (Low Gain)
Low Freq (Low Frequency)
Low Q
Low Type
Mid Gain (Middle Gain)
Mid Freq (Middle Frequency)
Mid Q (Middle Q)
High Gain
High Freq (High Frequency)
High Q
Hi Type (High Type)
Level (Output Level)
*1: If Low Type (Lo Type) or High Type (Hi Type) is set to "Shlv (Shlving Type)," the setting for Lo Q or High Q is invalid.
* "Gate Reverb" cannot be used on EFFECT2, 4, and 6 (even-numbered effects).
Direct Level
Gate Reverb
Direct Level
Accent sound
Accent
Reverb Level
Level (AcLvl)
(EfxLvl)
Time
Accent Delay Time
(AcDLY)
Setting Function
Mutes the revert sound midway.
On, Off Turns the gate reverb on or off.
See the column on
the previous page. Defines how the reverb sound is applied.
10–400 s Sets the time from when the reverb sound begins until it is muted.
0–300 ms Sets the time until the reverb sound appears.
0–100 Sets the thickness of the reverb sound.
0–100 Sets the density of the reverb sound.
0–200 ms Sets the time from when the reverb sound is muted until the accent sound appears.
0–100 Sets the volume of the accent sound.
L63–R63 Sets the pan of the accent sound.
-100–100 Sets the volume of the gate reverb sound.
-100–100 Sets the volume of the direct sound.
On, Off Turns the equalizer on or off.
-12– +12 dB Sets the boost/cut amount in the low frequency band.
20 - 2000 Hz Sets the center frequency in the low frequency band.
0.3–10.0 Sets the width of the area around the low frequency that will be affected by the gain settings.
Shlv, Peak Sets the type of the low frequency band equalizer (Shlving type or peaking type).
-12– +12 dB Sets the boost/cut amount in the middle frequency band.
200–8000 Hz Sets the center frequency in the middle frequency band.
0.3–10.0 Sets the width of the area around the middle frequency that will be affected by the gain settings.
-12– +12 dB Sets the boost/cut amount in the High frequency band.
1.4–20.0 kHz Sets the center frequency in the High frequency band.
0.3–10.0 Sets the width of the area around the High frequency that will be affected by the gain settings. *1
Shlv, Peak Sets the type of the High frequency band equalizer (Shlving type or peaking type).
0–100 Sets the volume after passing through the equalizer.
Output L
3BAND EQ
3BAND EQ
Output R
Reverb applications
You can select how reverb sounds can be applied by
setting up Gate Mode (Mode).
Normal: Ordinary Gate Reverb
L->R: The Gate Reverb sound moves from the left to
right side.
R->L: The Gate Reverb sound moves from the right to
left side.
Reverse1: Reverse Gate (effect as if reverb are replayed
backward.)
Reverse2: Reverse Gate that causes the reverb sound to
decay midway.
*1
25