Roland VS-2000 Appendices page 44

Algorithm List
Vocal Multi
This feature provides a multi-effect suited for vocals.
fig.08-30
Input L
Noise
Suppressor
Input R
Cutting distortion in vocals
Limiter can be used to suppress signals at a High level to prevent sound distortion. To do this, follow the steps below:
Mode (Mode):
Limiter Threshold (Thresh):
Limiter Release (Release):
Limiter Level (Level):
Cutting the sibilant sounds of a voice.
De-esser can be used to cut off sibilant sounds contained in vocal sounds to achieve softer sound quality. To do this, follow
the steps below:
Mode (Mode):
De-esser Sense (Sens):
De-esser Frequency (Freq):
Parameter (full name)
NS (Noise Suppressor):
Sw (Switch)
Thresh (Threshold)
Release (Release)
Lmt (Limiter / De-esser):
Sw (Switch)
Mode (Mode)
Thresh (Limiter Threshold)
Release (Limiter Release)
Level (Limiter Level)
ENH (Enhancer):
Sw (Switch)
Sens (Sense)
Freq (Frequency)
MixLvl (Mix Level)
Level (Level)
EQ (Equalizer)
Sw (Switch)
Low Gain (Low Gain)
Low Freq (Low Frequency)
Low Q
Low Type
Mid Gain (Middle Gain)
Mid Freq (Middle Frequency)
Mid Q (Middle Q)
High Gain
High Freq (High Frequency)
High Q
Hi Type (High Type)
Level (Output Level)
Pshift (Pitch shifter):
Sw (Switch)
Chromatic Pitch
Fine Pitch
FX Lvl (Effect Level)
DirLvl (Direct Level)
44
Limiter/
Enhancer
De-esser
Limiter
Sets the volume at which sound distortion starts being suppressed.
Determines the time that elapses before the input level becomes off after it drops below the Limiter Threshold.
Decides the volume after passing through Limiter.
De-esser
Sets the degree of the De-esser effect.
Sets the frequency at which De-esser effect starts working.
Setting Function
Mutes noise in the silent mode.
On, Off Turns the noise suppressor on or off.
0–100 Sets the level to start muting noise.
0–100 Sets the time over which the volume will drop to 0 after the noise starts being muted.
Suppresses signals at High levels to control distortion /
Suppresses the annoying s-consonant.
On, Off Turns the limiter/de-esser on or off.
Limiter, De-esser Selects limiter or de-esser.
0–100 Sets the volume at which sound distortion starts being suppressed.
0–100 Sets the time until when the limiter will turn off after the input level falls the limiter Threshold
(Thresh).
0–100 Sets the volume of the limiter sound.
Accentuates the sound and push the sound forward.
On, Off Turns the enhancer on or off.
0–100 Sets the degree of the enhancer effect desired.
1.0–10.0 kHz Sets the frequency at which the enhancer effect starts working.
0–100 Sets the amount of the enhancer sound should be mixed into the direct sound.
0–100 Sets the volume of the enhancer sound.
On, Off Turns the equalizer on or off.
-12– +12 dB Sets the boost/cut amount in the low frequency band.
20 - 2000 Hz Sets the center frequency in the low frequency band.
0.3–10.0 Sets the width of the area around the low frequency that will be affected by the gain settings.
Shlv, Peak Sets the type of the low frequency band equalizer (Shlving type or peaking type).
-12– +12 dB Sets the boost/cut amount in the middle frequency band.
200–8000 Hz Sets the center frequency in the middle frequency band.
0.3–10.0 Sets the width of the area around the middle frequency that will be affected by the gain settings.
-12– +12 dB Sets the boost/cut amount in the High frequency band.
1.4–20.0 kHz Sets the center frequency in the High frequency band.
0.3–10.0 Sets the width of the area around the High frequency that will be affected by the gain settings. *1
Shlv, Peak Sets the type of the High frequency band equalizer (Shlving type or peaking type).
0–100 Sets the volume after passing through the equalizer.
shifts the pitch.
On, Off Turns the pitch shifter on or off.
-12–12 Pitch variation (by semitone)
-100–100 Pitch variation (by cent)
-100–100 Sets the volume of the pitch shift sound.
-100–100 Sets the volume of the direct sound.
3BAND EQ Pitch Shifter
Output L
Delay
Chorus
Output R
*1