Table of Contents
Advertisement
FcInitiator
Allows FibreBridge to operate as an initiator on the Fibre Channel network, an attribute required for features such as Extended Copy.
Actions: set FcInitiator [enabled | disabled]
SaveConfiguration
FcPortFailure
Controls the behavior of a FC port when the FibreBridge is operating in AddressMap B. (failover) mode.
Limits: [Recover] will try to reset the FibreBridge to its pre-failover state. the recover mode must be past the index of the failed FC port
[Force] will create one of three types of simulated port failure on the specified active FC port for testing and demonstration.
.....
[loopdown] loss of FC synchronization (pulled cable, bad GBIC, etc.)
.....
[Isperr] simulates an internal ISP chip fatal error
Actions: FcPortFailure fp [recover| force [loopdown | portdown | isperr] ] Information: none
FcPortList
Returns a list of available Fibre Channel ports and their current status. Valid status values are OK and Failed.
Actions: none
FcSCSIBusyStatus
Specifies the SCSI status value returned when the FibreBridge is unable to accept a SCSI command because of a temporary lack of resources.
Limits: [busy | qfull]
Actions: set FcSCSIBusyStatus [busy | qfull]
SaveConfiguration
FcTargets
Obtains information about every Fibre Channel target device visible to a FibreBridge operating in initiator mode; devices may be used as targets
for initiator mode features such as Extended Copy.
Actions: none
FcWWName
Reports the Word Wide Name (WWN) of the Fibre Channel interface. Each FC port has an individual and unique WWN. The least significant 6 bits
of the WWN are used as the Ethernet MAC address.
Limits: Fabric and loop operations are unpredictable if duplicate WWNs are assigned.
Actions: none
FibreBridgeTargetLUN
Specifies the soft target LUN(s) to be used by the FibreBridge when addressed by the host as a SCSI device.
Limits: Any map coinciding with the user-specified FBTarget LUN must first be set to offline before trying to change it. This map will be destroyed upon
power-cycling the FB. Disabling a FibreBridgeTargetLUN for a particular FC port will destroy the map to the FB2300 for that port. The get form reports
all FB Target LUNs currently NOT disabled. Specifying a port returns the status of that port.
Action: set FibreBridgeTargetLUN [fp] [fl] | [disabled] ]
SaveConfiguration
Performance
Returns the performance data for the Fibre Channel port you specify. Data includes the average rate (MBs per sec.) and number of I/Os measured
over the previous sampling period. A FC port which has been disabled or has failed will prompt an error message. Reported performance may be
affected by FC port and SCSI bus availability and saturation, SCSI device speeds and overall system use.
Action: none
ServicesLUN
Sets and displays the Services LUN for the specified Fibre Channel port. Valid ServicesLUN entries are 0 through (n-1) where n equals the number
of Fibre Channel ports. Valid entries for fl are 0-64. Any map coinciding with a user-specified ServicesLUN must be set to offline before trying to
change a ServicesLUN.
Action: set ServicesLUN [fp] [fl] | [disabled] ]
SaveConfiguration
Information: get FcInitiator
.....
[portdown] simulates ISP chip hardware failure as detected by a fabric
Information: FcPortList
Returns: [line count] [fp] [status]
Default: busy
Information: get FcSCSIBusyStatus
Information: FcTargets
Returns: Node Name, FC LUN & inquiry data for each FC device found
Information: get FcWWN [PortNumber]
Return: Port n FcWWName= 20 00 00 10 86 nn nn nn
Information: get FibreBRidgeTargetLUN [fp]
Returns:
[Line Count]
[fp] [fl]
Information: get Performance [fp]
Information: get ServicesLUN [fp]
Returns:
[Line Count]
[fp] [fl]
24
Advertisement
Table of Contents
