Deif AGC 150 Operator's Manual
  1. Manuals
  2. Brands
  3. Deif Manuals
  4. Control Systems
  5. AGC 150
  6. Operator's manual
Deif AGC 150 Operator's Manual

Deif AGC 150 Operator's Manual

Hide thumbs Also See for AGC 150:
Table of Contents

Advertisement

Quick Links

Download this manual
AGC 150 Stand-alone
Operator's manual

Advertisement

Table of Contents
loading

Related Manuals for Deif AGC 150

Summary of Contents for Deif AGC 150

  • Page 1 AGC 150 Stand-alone Operator's manual...

  • Page 2: Table Of Contents

    1.1 Symbols for hazard statements ......................................1.2 About the operator's manual ....................................... 1.3 Warnings and safety ..........................................1.4 Legal information ............................................2. About the AGC 150 Stand-alone 2.1 Display, buttons and LEDs ........................................2.2 Display settings ............................................2.3 Mimic function ............................................. 2.4 Running modes ............................................

  • Page 3: Introduction

    1. Introduction Symbols for hazard statements DANGER! This shows dangerous situations. If the guidelines are not followed, these situations will result in death, serious personal injury, and equipment damage or destruction. WARNING This shows potentially dangerous situations. If the guidelines are not followed, these situations could result in death, serious personal injury, and equipment damage or destruction.

  • Page 4: Warnings And Safety

    Legal information Third party equipment DEIF takes no responsibility for the installation or operation of any third party equipment, including the genset. Contact the genset company if you have any doubt about how to install or operate the genset. Warranty...

  • Page 5: About The Agc 150 Stand-Alone

    2. About the AGC 150 Stand-alone Display, buttons and LEDs Name Function Green: The controller power is ON. Power OFF: The controller power is OFF. Resolution: 240 x 128 px. Display screen Viewing area: 88.50 x 51.40 mm. Six lines, each with 25 characters.

  • Page 6: Display Settings

    Name Function Green: Breaker is closed. Breaker symbols Red: Breaker failure. Green: Generator voltage and frequency are OK. The controller can close the breaker. Green flashing: The generator voltage and frequency are OK, but the V&Hz OK timer is still Generator running.

  • Page 7: Running Modes

    Guided Active control buttons and LEDs are shown inactive are not shown. Example: The AGC 150 Stand-alone is in SEMI-AUTO mode, and the genset is not operating. Only the start button is shown, as this is the only possible action.
  • Page 8 Mode Description The controller cannot start a sequence, for example the start sequence. Select the block mode when you do BLOCK maintenance work on the genset. Test The test sequence will start when you select the test mode. NOTE The genset will shut down if you select the block mode while the engine is operating. Operator's manual 4189341311B EN Page 8 of 22...

  • Page 9: Menus

    3. Menus Menu structure The controller has two menu systems, which can be used without password entry: • The View menu system: Shows the operating status and values. The system has 20 configurable windows, that can be entered with the arrow buttons. •...

  • Page 10: Menu Numbers

    3.2.1 Menu numbers Each parameter has a menu number. You can find the number in the upper right corner on the display screen. You can also find the menu number with the utility software: 1. Select Parameters from the toolbar on the left. 2.

  • Page 11: Display Views

    1. Operating status 2. Values and information 3. Page number The view menu has 20 different display views. Use the buttons to select a view. Push 3.3.1 Display views The controller has 20 different display views and 17 of the views are pre-configured. You can configure the views with the utility software.

  • Page 12: Display Text

    Line View 11 View 12 View 13 View 14 View 15 P GTot and P % G Angle L1L2 0deg P 0kW 0% P available 0kW BB-Gen Angle 0deg Q GTot and Q % G Angle L2L3 0deg Q 0kvar 0% P available 0% G Angle L1L2 0deg BB Angle L1L2...

  • Page 13: Status Texts

    Display text You can select five of the display texts for each display view. Status texts Status text Condition ACCESS LOCK The configurable input is activated, and the operator tries to activate one of the blocked keys. AMF ACTIVE The controller is in auto mode during a mains failure. AMF AUTO The mains controller is in auto mode and ready to respond.

  • Page 14: Service View

    Status text Condition LOAD TAKE OVER MAN The controller is in manual mode and waiting for operator input. LOAD TAKE OVER SEMI The controller is in semi-automatic mode and waiting for operator input. LOAD TEST Test mode is activated. LOAD TEST ###.#min Test mode is activated and test timer counting down.
  • Page 15 Service view example Operator's manual 4189341311B EN Page 15 of 22...

  • Page 16: I/O Setup Menu

    I/O Setup menu You can configure digital inputs, multi inputs, digital outputs, and external inputs/outputs on the controller. On the controller 1. Push the OK button to see the different menus. 2. Select I/O Setup. 3. Select the type of input you want to configure, for example digital inputs. 4.

  • Page 17: General Shortcuts

    You can see your configured shortcuts in the General shortcuts menu. If you have not configured a shortcut, then the menu is empty. Use the shortcuts when the controller is in SEMI-AUTO and manual mode. More information See General shortcuts in the AGC 150 Stand-alone Designer's handbook for how to configure the general shortcuts. On the controller 1.

  • Page 18: Exhaust After-Treatment (Tier 4/Stage V)

    Exhaust after-treatment (Tier 4/Stage V) AGC 150 meets the Tier 4 (Final)/Stage V requirements. The user can use the display to monitor (and control) both the engine, and the exhaust after-treatment system. After-treatment page Referent Symbol Description After-treatment status Engine emission system failure Emission failure or malfunction.
  • Page 19 Referent Symbol Description Diesel Particle Filter (DPF) level Regeneration needed, with the severity. DEF level warning Low DEF level. DEF shutdown DEF problem stops normal operation. Mid-level inducement. DEF level inducement Severe inducement. Diesel Exhaust Fluid (DEF) DEF quality is low. Engine dashboard Operator's manual 4189341311B EN Page 19 of 22...
  • Page 20 Referent Symbol Description Water in fuel There is water in the fuel. Engine interface status An engine warning. Page name Controller status Engine interface status An engine shutdown. Engine interface status An engine malfunction. Cold start The engine is cold. High engine coolant temperature The engine coolant temperature is high.

  • Page 21: Alarm Handling And Log List

    4. Alarm handling and log list Alarm handling If the function Alarm Jump is on, the controller will automatically show the alarm list on the display screen when an alarm occurs. Service View > Display > Alarm Jump Parameter Text Range Default 9157...

  • Page 22: Logs Menu

    CAUTION Caution If an alarm is blocking a genset in AUTO mode from starting, the genset will automatically start if the condition that triggered the alarm has gone and the alarm has been acknowledged. Logs menu These are the log sub-menus: 1.

Table of Contents