Advertisement
Quick Links
Advertisement
Related Manuals for aivituvin AIR 27
Summary of Contents for aivituvin AIR 27
- Page 1 INSTRUCTION MANUAL AIR 27 www.aivituvin.com...
- Page 2 NOTICE Please retain these instructions for future reference. Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals.
-
Page 3: Tools Required
TOOLS REQUIRED PHILLIPS DRILL 2PERSON APPROXIMATELY SCREWDRIVER (RECOMMENDED) ASSEMBLY 45MIN. ASSEMBLY HARDWARE M3.5x60mm SCREW M6.0x30mm BOLT 10PCS+1spare 8PCS+1spare M3.5x35mm SCREW M3.5x45mm SCREW 2PCS+1spare 30PCS+1spare M3.5x25mm SCREW M3.0x16mm SCREW 7PCS+1spare 36PCS+1spare Connect pieces M4.0x30mm BOLT 2PCS 2PCS (Only for 2 coops combination. not available for one coop owner) - Page 4 HARDWARE Spring latch Lock 3PCS Lock...
- Page 5 Coop Nesting box...
- Page 6 PARTS CARTON 1/2 Front panel of coop Left panel of coop Back panel of coop Right panel of coop Front panel of pen Side panel of pen...
- Page 7 PARTS Metal ramp support Front panel of nest box Perch 2PCS Hardware bag Casters Ramp 2PCS Metal Rod...
- Page 8 PARTS CARTON 2/2 Roof of pen Metal tray Bottom panel of nest box Push handle Divider of nest box Roof of nest box Roof of coop Roof cap PVC Waterproof Strip 2PCS...
-
Page 9: Product Assembly
PRODUCT ASSEMBLY ① Attach the front Part B,the back Part A to the Part C & D by 8xP4. ② Notice to align with the dowels. Insert perch Part O into slots inside Part A & B. ① Slide in metal tray Part E. ② ... - Page 10 PRODUCT ASSEMBLY Ensure that all pen-panels have stapled-wire facing inside. ① ② Attach Part F & G to coop by 4xP2. ③ Attach metal ramp support Part V to the back panel by 2xP7. ① Screw ladder Part N to the bottom half of lower panel on Part D by 4xP6.
- Page 11 PRODUCT ASSEMBLY Attach Part H to the pen sides by 4xP4. ① Notice to align with the dowels. ② Attach metal rod to the slide door of panel Part D by 2xP6. ③ Attach Part L to Part J & K by 4xP4. ① ...
- Page 12 PRODUCT ASSEMBLY Attach the nesting box to the coop by 1xP4 & 1xP2 each side. ① (Notice screw the P4 from inside in the upper position, screw the P2 from outside in the down position) Drop in nest box floor Part M. ②...
- Page 13 PRODUCT ASSEMBLY Attach roof of nesting box Part R to the coop by 4XP6. Attach the roof Part I by 4xP4 to complete side pen. ① ② Attach the lock P11 to the pen by 4XP6. P 11...
- Page 14 PRODUCT ASSEMBLY Screw the push handle Part Q to the side pen by 4xP2. Screw roof panels Part S to the coop by 8xP4. ① Attach the lock P10 to the tray by 6XP6. ②...
- Page 15 PRODUCT ASSEMBLY Ensure top roof panels line up with each other before screwing Part ① T by 4xP5. Attach PVC Waterproof Strip Part W to the nesting box by 3XP5. ② Attch spring latch P9 by 2xP6 each. Notice the direction of spring latch. Finish here for only buying one coop...
- Page 16 Notice Read Before Assemble! ① Pls ignore the following for only one coop owner ! ② The caster, the side pen panel Part H, the push handle Part Q, the metal rod ,the pen lock P11 are not needed in 2nd coop. ③ ...
- Page 17 Notice Read Before Assemble! ① From Step 15 to Step 16 are assemble step for 2nd coop. ② The caster, the side pen panel Part H, the push handle Part Q, the metal rod are not needed in 2nd coop.
- Page 18 PRODUCT ASSEMBLY ① Notice the direction of Part C & D is different with the 1st coop. ② (Very important) ③ Repeat the same assembly ways from step 2-step13 the same as the 1st coop. ！ Notice the direction of Part C &...
- Page 19 PRODUCT ASSEMBLY Attch spring latch P9 by 2xP6 each. Notice the direction of spring latch.
- Page 20 OPTION 1 Take out the casters for the first coop. ① Push upward the hinge to take out the door of the front pen of the ② 1st coop. Take out the spring latch on the pen of the 1st coop. ③...
- Page 21 PRODUCT ASSEMBLY...
- Page 22 OPTION 2 Take out the casters of the first coop. ① Take out the side pen panel Part H of the first coop. ② Take out the pen lock of the first coop. ③ (Suggest to use pliers) TAKE OUT ! Dowel x 2...
- Page 23 PRODUCT ASSEMBLY Screw the Connect Piece 2xP8 to the middle frame of the 2 coops by 4xP6 each side.
- Page 24 WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this product.
Need help?
Do you have a question about the AIR 27 and is the answer not in the manual?
Questions and answers