Programming The User Message - 1835 System - DoorKing 1835 Owner's Manual

3.4.2 Programming the User Message – 1835 System
The user message, followed by the instruction message, scrolls across the screen from right to left
when the system is not in use. Both the user and instruction message can be programmed to display your
own message. The user message can be a maximum of 48 characters (spaces count as a character) and
is entered into the system memory in three blocks. The first two blocks contain 20 characters while the
third block contains 8 characters. The example below shows how the sample message was divided into
three blocks. Use the blank table to organize your own message. Only upper case letters, numbers and
spaces can be programmed from the system keypad.
Factory Default User Message = This Space is For YOUR Scrolling User Programmable Message.
Example: THANK YOU FOR VISITING OAKWOOD CONDOMINIUMS
1 2
Block 1
T H
Block 2 N G
U M
Block 3
Note: The factory default message was programmed from a PC, therefore upper and lower case letters are displayed.
1 2
Block 1
Block 2
Block 3
After organizing the user message in the table above, follow the instructions below to enter the message into the system. After
each desired letter, number or space is displayed on the directory, remember to press
a character and must be entered into memory as a character. After a complete block of characters (including spaces) has been
entered, press to enter the block, then start the next block.
*
TUV TUV OPER OPER
1. Press and enter your four-digit MASTER CODE
8 8 0 0
The LCD display on the 1835 will read: BLOCK 1.
2. Enter the characters into block 1 (refer to 3.4.1 for reference). Remember to press
3. After the last character in block 1 has been entered, press
The LCD display will read: BLOCK 2.
4. Enter the characters into block 2. Remember to press
5. After the last character in block 2 has been entered, press
The LCD display will read: BLOCK 3.
6. Enter the characters into block 3. Remember to press
7. After the last character in block 3 has been entered, press
8. Press (beep) to enter all three blocks into the system memory.
OPER OPER
9. Press together to end this programming sequence (beeeeeep).
0 0
10. The new user message will begin to scroll across the screen.
38
3 4 5 6 7
A N K Y
O A K W
S
3 4 5 6 7
8 9 10 11 12
O U F O
O O D C
8 9 10 11 12
? ? ? ? ? ?
(beep) to enter the entire block.
(beep) after each character.
(beep) to enter the entire block.
(beep) after each character.
(beep) to enter the entire block.
13 14 15 16 17
R V I S
O N D O M
13 14 15 16 17
to enter that character. Spaces count as
*
? ?
(beep).
(beep) after each character.
TELEPHONE ENTRY SYSTEM
SP SP ABC ABC DEF DEF
1 1 2 2 3 3
GHI GHI JKL JKL MNO MNO
4 4 5 5 6 6
PQRS PQRS TUV TUV WXYZ WXYZ
7 7 8 8 9 9
OPER OPER
0 0
HOLD TO SCAN
A
OPERATING INSTRUCTIONS
1. Use "A to Z" Buttons to Locate
Name and Code Number on Display. Z
Names are In Alphabetical Order.
2. To Call, Enter Code Number on
Keypad or Press "Call" Button. If
Line is Busy, Press "#" or "Call" to
Hang Up. Try Again.
CALL
3. Enter on Open Display and Tone.
18 19 20
I T I
I N I
18 19 20
1835-065-D-5-17