YASKAWA T103 Installation & Primary Operation page 11

Item
• V/f Control
• V/f Control with Encoder
• Open Loop Vector
• Closed Loop Vector
Control Methods • Advanced Open Loop Vector
• PM Open Loop Vector
• PM Advanced Open Loop Vector
• PM Closed Loop Vector
• EZ Vector Control
HD: 5 kHz without derating the drive capacity.
Carrier Frequency ND: 2 kHz without derating the drive capacity.
Derate the drive capacity to use values to 10 kHz maximum.
Three-phase 380 V to 480 V
Maximum Output
Note:
Voltage
The maximum output voltage is proportional to the input voltage.
• AOLV and EZOLV: 0.01 Hz to 120 Hz
Frequency Control
• CL-V/f, CLV, AOLV/PM, and CLV/PM: 0.01 Hz to 400 Hz
Range
• V/f, OLV, and OLV/PM: 0.01 Hz to 590 Hz
Frequency Accuracy Digital inputs: ±0.01% of the maximum output frequency (-10 °C to +40 °C (14 °F to 104 °F))
(Temperature
Analog inputs: In ±0.1% of the maximum output frequency (25 °C ±10 °C (77 °F ±18 °F))
Fluctuation)
Digital inputs: 0.01 Hz
Frequency Setting
Resolution
Analog inputs: 1/2048 of the maximum output frequency (11-bit signed)
Output Frequency 0.001 Hz
Resolution
Main speed frequency reference: -10 Vdc to +10 Vdc (20 kΩ), 0 Vdc to 10 Vdc (20 kΩ), 4 mA to 20 mA (250 Ω), 0 mA to 20 mA (250 Ω)
Frequency Setting
Signal
Main speed reference: Pulse train input (maximum 32 kHz)
• V/f: 150%/3 Hz
• CL-V/f: 150%/3 Hz
• OLV: 200%/0.3 Hz
• CLV: 200%/0 min
• AOLV: 200%/0.3 Hz
• OLV/PM: 100%/5% speed
• AOLV/PM: 200%/0 min
• CLV/PM: 200%/0 min
• EZOLV: 100%/1% speed
Starting Torque
Note:
• Correctly select the drive and motor capacity for this starting torque in these control methods:
–OLV
–CLV
–AOLV
–AOLV/PM
–CLV/PM
• Set n8-57 = 1 [HFI Overlap Selection = Enabled] for this starting torque in AOLV/PM. When you use a non-Yaskawa PM motor, do Rotational Auto-
Tuning.
• V/f: 1:40
• CL-V/f: 1:40
• OLV: 1:200
• CLV: 1:1500
• AOLV: 1:200
• OLV/PM: 1:20
Speed Control Range
• AOLV/PM: 1:100
• CLV/PM: 1:1500
• EZOLV: 1:100
Note:
• Set n8-57 = 1 [HFI Overlap Selection = Enabled] for this Speed Control Range in AOLV/PM. When you use a non-Yaskawa PM motor, do Rotational
Auto-Tuning.
• Speed control range of 1:100 for AOLV/PM is Instantaneous operation range. Correctly select the drive and motor capacity for continuous operation.
Possible in these control methods:
• CLV
Zero Speed Control
• AOLV/PM
• CLV/PM
YASKAWA TOEPC71061782C GA800 Drive Installation & Primary Operation
Table 5.1 Control Characteristics
-1 (r/min)
-1
(r/min)
-1 (r/min)
5 Common Drive Specifications
Specification
11