Table of Contents
Advertisement
Setting warning levels on a VHX system:
1. Hold the SW1 (I) switch from the instrument system control box while turning the key on.
a. The message display should show SETUP.
2. Release SW1 (I) - LCD1 should show SETUP SPEED.
3. Tap SW1 (I) until SETUP BIM is shown on the message display.
4. Press and hold SW1 (I).
a. The message display will show SCANNING... Release SW1 (I).
b. The display will scroll through the 16 possible channels used.
5. If FOUND 00 and 00 ERRORS is shown:
a. Check and reseat all BIM connections.
b. Tap SW1 (I) to show BIM DONE. Tap SW1 (I) again to show BIM SCAN.
c. Press and hold SW1 (I) to scan for modules again.
6. If FOUND 00 and XX ERRORS is shown (X= a number):
a. If multiple BIM units may be installed, the display may also show: FOUND 01 and 00 ERRORS.
b. Follow the "Change ID" for other BIM modules to correct conflicts, the enter setup again start over.
7. If FOUND xx and 00 ERRORS shown (X=should be the number of BIM channels used):
a. One BIM-22-3 will read: FOUND 04 and 00 ERRORS.
b. If a BIM-22-3 is used with a BIM-19-2 the scan should read: FOUND 08 and 00 ERRORS.
c. Tap SW1 (I) until BIM SCAN is shown.
8. Tap SW1 (I) once so the display shows BIM SETUP.
a. The BIM setup options are SCAN, SETUP, and DONE.
9. Tap SW1 (I) once to display SETUP.
10. Press and hold SW1 (I) until the display will show BIM CH 03 LF TIRE.
a. If another BIM is present, you may see more BIM channels.
b. A BIM-04-2 will occupy BIM CH 1 TEMP.
c. Tap SW1 (I) to display BIM CH 3 LF TIRE.
11. Press and hold SW1 (I) to change display to CH 03 LABEL LF TIRE.
a. The BIM-22-3 module will flash . It is not a problem during setup
12. Press and hold SW1 (I) until CH 03 LOW WARN SET is displayed.
13. Releasing SW1 (I) will display the LF corner low air pressure warning point of 25 (factory default).
14. Tap SW1 (I) to increment the low-pressure warning point.
a. If 25 PSI is sufficient as a low-pressure point, press and hold SW1 (I) to save.
b. Low pressure range is from 05 to 99 PSI.
c. If you tap past your desired PSI, you must tap up 99 before it restarts at 05 PSI.
15. Press and hold SW1 (I) to save low pressure warning – CH 03 HI WARN SET will be display.
16. Releasing SW1 (I) will display the LF corner high air pressure warning of 35 (factory default).
17. Tap SW1 (I) to increment the high-pressure warning point.
a. If 35 PSI is sufficient as a high-pressure, point press and hold SW1 (I) to save.
b. Low pressure range is from 05 to 99 PSI.
c. If you tap past your desired PSI, you must tap up 99 before it restarts at 05 PSI.
18. Press and hold SW1 (I) to save high-pressure warning point.
19. When SW1 (I) is released, TIRE LOCATE SKIP will be displayed.
a. To do the TIRE LOACTE proceed to the next page.
b. To skip over Tire Locate press and hold SW1 (I) until BIM CH 04 rF TIRE.
c. Repeat step 11 to step 19 for remaining tires.
20. If done setting warning points and locations, tap SW1 (I) until BIM SETUP DONE is displayed.
21. Press and hold SW1 (I) until a big DONE is displayed. Release SW1 (I) and turn the key off.
[5]
MAN #650793
Advertisement
Table of Contents
Troubleshooting
