Bim-22-3; Sensor Location And Warning Levels - Hdx And Rtx - Dakota Digital BIM-22-3 Manual

Setting Warning Levels on an HDX or RTX system:
1. HDX – Enter setup by holding both switches after the key is turned on.
a. Continue to hold until RELEASE is displayed. Release the switches.
2. RTX – Enter setup by holding Switch 1 (SW!) then turn the key on.
a. Release the switch when SETUP is displayed on the LCD.
3. Tap either switch to display BIM.
4. Press and hold either switch when
5. Tap either switch to highlight one of the four BIM-22-3 corners
a. Each corner sensor is associated to a BIM channel.
b. If multiple BIMs are attached and there is conflict, hold the setup button on one of the smaller BIMs
whiling turning the key on. That BIM will automatically adjust all BIM channels to avoid conflicts.
6. Press and hold either switch on a selected channel until the display shows RELEASE - then release.
7. New sub-menu options are WARN LO, WARN HI, LOCATE, and BACK.
8. Tap either switch to highlight
9. Press and hold either switch until the display say RELEASE – then release.
10. The corner selected will display the low-pressure waning in highlighted red.
11. Tap SW1 or left switch to decrease pressure.
12. TAP SW2 or right switch to increase pressure.
13. Press and hold either switch to display RELEASE to save the desired low pressure warning point.
14. The menu will go back to WARN LO, WARN HI, LOCATE, and BACK in step 7.
15. You can set the WARN HI in the same manner as the WARN LO, or tap to highlight BACK to return.
16. Press and hold when
17. Repeat Step 5 for the remaining corner sensors, or go to BACK and hold to exit.
Locating Sensors on an HDX or RTX system:
1. HDX – Enter setup by holding both switches after the key is turned on.
a. Continue to hold until RELEASE is displayed. Release the switches.
2. RTX – Enter setup by holding Switch 1 (SW!) then turn the key on.
a. Release the switch when SETUP is displayed on the LCD.
3. Tap either switch to display BIM.
4. Press and hold either switch when
5. Tap either switch to highlight one of the four BIM-22-3 corners
6. Press and hold either switch on a selected channel until the display shows RELEASE - then release.
7. New sub-menu options are WARN LO, WARN HI, LOCATE, and BACK.
8. Tap either switch to highlight
9. Press and hold either switch until the display shows RELEASE – then release.
a. If the message FILL LOW TIRES is displayed, fill tires to above the low pressure warning.
b. If no tire pressure(s) are being shown for a corner, deflate and inflate tires to display a pressure.
c. If one or more tire pressures do respond after several deflates and inflates over a couple of minutes,
and the display shows "- -", then stop and proceed to page 7.
10. DEFLATE LEFT FRONT will display – deflate a little pressure from that tire on the car.
a. If the car has been stationary for more than 15 minutes, it will take 60 seconds to see changes.
b. If the car was driven 5-10 minutes before starting LOCATE, the response time will be 5 seconds.
c. When the pressure sees a change, the instructions will say to change to another tire.
11. DEFLATE RIGHT FRONT will display – deflate a little pressure from that tire on the car.
12. DEFLATE LEFT REAR will display – deflate a little pressure from that tire on the car.
13. FILL LOW TIRES will appear as the Right Rear does not need deflating.
14. Inflate the three lower pressure tires to the proper tire pressure.
15. Tap either switch to return to the previous menu.
16. You may exit the menu as
is highlight, wait until RELEASE is displayed – then release.
BIM
WARN LO to set a low warning pressure.
BACK is highlighted to return to the four corners selection menu in step 5.
is highlight, wait until RELEASE is displayed – then release.
BIM
LOCATE to change sensor locations.
is highlighted – press and hold until RELEASE, then release.
BACK
[4]
(3

BIM-22-3).

(3 BIM-22-3).
MAN #650793