Related Manuals for OMP Hobby OMPHOBBY
Summary of Contents for OMP Hobby OMPHOBBY
- Page 1 Global Professional RC Model Brand Installation Manual OMPHOBBY 60” 70E Edge 540 Kevlar Reinforced Balsa Airplane Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 2 OMPHobby 60” Balsa Airplane OMPHobby 60” 70E EDGE 540, not only has the low speed stability, low stall point, excellent 3D performance, but also very fast roll rate of traditional EDGE, and precise navigation control. The traditional securing method of the motor base and the landing skid base have been changed, preventing the loosening of the ant i- graspi ng nut.
- Page 3 OMPHobby 60” Balsa Airplane Parameter Specification Green-Black Red-White Item: OMPHOBBY 60”EDGE 540 Color Option Yellow-White Orange-White WingSpan: 1524mm(61in) Full Length: 1500mm(60in) The Center of Flight Weight: 2.75~2.85KG Approx.86-95mm Gravity (CG): Wing Area: Wing Load: 42.32d㎡ 64.98~67.34g/d㎡ Wing Angle of Motor Thrust 0°...
- Page 4 OMPHobby 60” Balsa Airplane Ø Package contents (ARF version) Ø Tools and Gear needed Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 5 3. Apply glue to the screws and install motor to motor holder. Ø ESC Installation 1. Attach connected ESC to ESC holder with double-sided tape and Secure with cable ties. 2. Tie the wires of ESC and motor with fastening strap. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 6 1.5mm. 4. Secure the cowl with screws, two screws for each of two sides.secure Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 7 3. Put landing gear cover plate into slot and stick it with transparent tape. 4. Install landing gear cuffs, Secure it with electrical tape. 5. Install wheels, Secure wheels with gasket and screw. (Apply glue to screws) Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 8 Landing gear Assembly 6. Install wheel cowls, tighten screws. Tail wheel Assembly Ø Tail Wheel Installation 1. Find the securing hole of the tail wheel frame, secure the tail wheel bracket with screws. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
-
Page 9: Installation
4. Secure the servo using the screws. Ø Horizontal Tail Installation 1. Carefully locate the slot which has been made on horizontal tail, lightly cut through the covering but not into the balsa sheeting. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com... - Page 10 4. Insert secured plate to fill the horizontal tail slot, use 502 gluing the gap all around the horizontal tail. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 11 6. Secure screw, washer, ball head to control horn. 7. Check the angle between the servo arm and control horns. (Make sure the control horn is at 90 degrees against servo.) Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 12 4 hinges into the rudder. 4. Inject AB glue into the holes in fuselage, apply glue to the other end of hinges with appropriate length, then insert it into fuselage. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 13 10. After the glue is dried, secure the servo arm and control arms with a ball head pull rod. 11. Make sure the angle of servo and control horns is 90° 180°oblique, ensure rudder is symmetrical to the 2 sides of fuselage. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 14 3. Pull out the white polyester thread from the servo hole with tweezers, tie up with aileron servo connector. 4. Find the other head of white polyester thread from wing side, pull it until aileron servo is placed in servo hole. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 15 7. Secure screw, washer, ball head to control arm, control arm is at 90 degrees against servo. 8. Check the degrees between servo arm and control arms. Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 16 9. Assemble the wing tube into the fuselage then install wings, turn white screws to secure the wings. 10. Unscrew the retaining screws on the wing, install wingtip. Connect Receiver and Battery Zhuhai Edge Smart Drive Technology Co., Ltd. www.omphobby.com...
- Page 17 OMPHobby 60” Balsa Airplane For customer support in the USA, please For customer support outside of the USA, contact Ohio Model Products in Ohio. please contact OMPHobby in China. Tel: +1-614-733-9488 (9am -5pm, ET) Email: store@omphobby.net Email: support@omphobby.com Website: www.omphobby.com Website: www.OhioModelProducts.com...