1. Manuals
  2. Brands
  3. Boser Manuals
  4. Single board computers
  5. HS-6300
  6. Manual

Boser HS-6300 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BX Dual Pentium
• Full Size•All-in-one•VGA/Flat-Panel Interface•DMA33-IDE•
• LAN•ATX Power•WDT•DOC•CTA•USB•
• IrDA PICMG Bus Industrial Single Board Computer•
BX Dual Pentium
• Full Size•All-in-one•VGA/Flat-Panel Interface•DMA33-IDE•
• ATX Power•WDT•DOC•CTA•USB•
•IrDA PICMG Bus Industrial Single Board Computer•
BX Dual Pentium
• Full Size•All-in-one•DMA33-IDE•
• LAN•ATX Power•WDT•DOC•CTA•USB•
•IrDA PICMG Bus Industrial Single Board Computer•
HS-6300
®
II/III LAN/VGA I.S.B.
HS-6300V
®
II/III VGA I.S.B.
HS-6300
®
II/III LAN I.S.B.

Advertisement

Table of Contents
loading

Related Manuals for Boser HS-6300

Summary of Contents for Boser HS-6300

  • Page 1 HS-6300 ® BX Dual Pentium II/III LAN/VGA I.S.B. • Full Size•All-in-one•VGA/Flat-Panel Interface•DMA33-IDE• • LAN•ATX Power•WDT•DOC•CTA•USB• • IrDA PICMG Bus Industrial Single Board Computer• HS-6300V ® BX Dual Pentium II/III VGA I.S.B. • Full Size•All-in-one•VGA/Flat-Panel Interface•DMA33-IDE• • ATX Power•WDT•DOC•CTA•USB• •IrDA PICMG Bus Industrial Single Board Computer•...
  • Page 2 Copyrights This manual is copyrighted and all rights are reserved. It is not allow any non authorization in copied, photocopied, translated or reduced to any electronic or machine readable in whole or in part form without prior written consent from the manufacturer. In general, the manufacturer will not be liable for any direct, indirect, special, incidental or consequential damages arising from the use of inability to use the product or documentation, even if advised of the possibility of such...

  • Page 3: Table Of Contents

    Contents HS-6300 ...................... 1 ® CAUTION OF PENTIUM II/III PROCESSOR MODULE INSTALLATION ............錯誤! 尚未定義書籤。 GENERAL INFORMATION ........錯誤! 尚未定義書籤。 1.1 M ..................5 AJOR EATURES ........... 錯誤 錯誤 錯誤! 尚未定義書籤。 錯誤 尚未定義書籤。 尚未定義書籤。 尚未定義書籤。 1.2 S PECIFICATIONS ..........錯誤 錯誤! 尚未定義書籤。...
  • Page 4 3.9 K ..............20 EYBOARD ONNECTORS 3.10 PS/2 M ......... 21 OUSE ONNECTOR 3.11 VGA C ................21 ONNECTORS 3.12 F ..............21 ANEL ONNECTOR 3.13 IR C ..................21 ONNECTOR 3.14 F .............. 21 THERNET ONNECTOR AWARD BIOS SETUP..................22 4.1 M .....................
  • Page 5 Contents • • • • iii...

  • Page 6: General Information

    I/O effects and VGA interface and Intel 82558B LAN. With on board DMA33 of mode 4 to IDE drive interface architecture, the HS-6300 supports with maximum 33.3MB/sec in data transfer rating to 4 pieces IDE drive ®...
  • Page 7 1.1 Major Features PICMG Bus supported. ® ® Two Slot 1 sockets for Dual Intel Pentium II/III Processors. ® Intel 82443 BX chipset. ® Intel 82558B LAN chip on board. Four pieces DIMM sockets supports DRAM & SDRAM up to 2GB. Fast PCI DMA33 controller supports four IDE drives include large hard disks, CD-ROM and tape backup etc.

  • Page 8: Specifications

    1.2 Specifications ® ® CPU：One or two pieces Intel Pentium II/III 233MHz higher. Bus Interface：PICMG Bus. ® Chipset：Intel 82443 BX. Data Bus：64bit. Processing Ability：64bit. CRT SVGA Controller：C&T 69000 chipset with 2MB memory supports CRT up to 1024x768 256 colors. PCI Enhanced IDE Interfaces：Four IDE drives supports modes 3/4 with DMA 33 function provide data transfer rate up to 33MB/sec.
  • Page 9 CMOS：Real-time clock/calendar and battery backup by DS12B887 or equivalent device. Power Supply Voltage：+5V(4.75 to 5.25V), +12V, -12V. Max. Power Requirement：+5V@22A(350MHz), +12V/-12V@20mA. Operating Temperature：0-55°C (CPU need cooler). Board Size：13.26”(L) x 4.8”(W) (337mm x 122mm).

  • Page 10: Delivery Package

    1.3 Delivery Package The Delivery package of HS-6300 includes all following items： HS-6300 Industrial Single Board One Printer Port Flat Cable One COM Port Flat Cable Two IDE Port Flat Cable FDD Port Flat Cable One PS/2 to Standard Keyboard Transfer Cable...

  • Page 11: Caution Of Static Electricity

    Hardware Installation This chapter provides the information on how to install the hardware of HS-6300. At first, please follow up sections 1.3, 2.1 and 2.2 in check the delivery package and carefully unpacking. Following after, the jumpers setting of switch, Watch-Dog Timer and the DiskOnChip address selection etc.

  • Page 12: Caution On Unpacking And 2.3 Hs-6300' S Layout

    HS-6300 from electricity discharge. With refer to section 1.3, please check the delivery package again with following steps： 1. Unpacking the HS-6300, keep well storage of all packing material, manual and diskette etc. 2. Is there any components lose or drop from the board？ DO NOT INSTALL IF IT HAPPENED.

  • Page 13: Quick Listing Of Jumpers

    2.3 HS-6300’s Layout 2.4 Quick Listing of Jumpers IOQ DEPTH Select Base Clock Clock Ratio Select Clock Ratio Select Clock Ratio Select Clock Ratio Select D.O.C Address setting Time of Watch-Dog ATX Power ON JMP JP10 Watch-Dog Active Select JP11...

  • Page 14: Quick Listing Of Connectors

    2.5 Quick Listing of Connectors CN1：ATX Power Connector CN2：5-pin Header Keyboard Connector CN3：Keylock CN4：Speaker CN5：LED Connector CN6：Reset Connector CN7：Primary IDE Connector CN8：Secondary IDE Connector CN9：LCD Panel Connector CN10：Panel Voltage Selection CN11：ATX Power & AT Power Selector CN12：Parallel Port CN13：FDD Connector CN14：COM2 (5x2 Header) CN15：COM1 (5x2 Header) CN16：10/100 Based LAN Connector...

  • Page 15: Jumper Setting Description

    2.6 Jumper Setting Description A jumper pin-set is ON as a shorted circuit with a plastic cap inserted over two pins. A jumper pin-set is OFF as a open circuit with a plastic cap inserted over one or no pin between pins. The below figure 2.2 shows the examples of different jumper pin-set setting as ON or OFF in this manual.

  • Page 16: Manufacture Defaults

    2.7 Manufacture Default Setting The HS-6300 has an on board manufacture default setting of JP1 as following： Default Setting of JP1： ： ： ： IOQ Depth Setting IOQ Depth of 4 *OFF IOQ Depth of 1 2.8 Setting the CPU’s Processor Core Frequency &...
  • Page 17 2.9 DiskOnChip Address Setting The HS-6300 provides a U22 socket for install the DiskOnChip module. A JP7 (pin 1-2, 3-4) may select the starting memory address of the DiskOnChip for avoid the mapping area with any other memory devices. If you have another extra memory devices in the system with the same memory, neither the HS-6011 nor the extra memory devices will function normally.

  • Page 18: Watch-Dog Timer

    2.10 Watch-Dog Timer There are three access cycles of Watch-Dog Timer as Enable, Refresh and Disable. The Enable cycle should proceed by READ PORT 443H. The Disable cycle after a first Enable cycle means Refresh. Once if the Enable cycle activity, a Refresh cycle is request before the time-out period for restart counting the WDT’s period.
  • Page 19 Refresh cycle to WDT before its period setting comes ending of every 1, 2, 10, 20, 110 or 220 seconds. If the Refresh cycle does not active before WDT period cycle, the on board WDT architecture will issue a Reset or NMI cycle to the system.

  • Page 20: Usb Ports Connector

    BD1- BD0+ BD1+ Ground Ground 2.12 Setting the RTC Configuration The HS-6300 provides a setting for the selection of the RTC Clear Jumper of JP4 setting as following： JP11： ： ： ： CMOS Setting JP11 CMOS Clear Jumper *OFF Normal Clear CMOS 2.13 System Memory DRAM...

  • Page 21: Pci Vga Controller

    2.14 PCI VGA Controller The HS-6300 has built-in a C&T 69000 VGA Controller. If you want to use the external VGA Card, the BIOS will automatically disable the on board VGA controller and use the external one. Video Modes C&T 69000 Chipset with 2MB memory, support resolutions up to 1280x1024 256 colors.

  • Page 22: Connection

    This chapter gives all necessary information of the peripheral’s connections, switches and indicators. 3.1 Power Connector The HS-6300 provides one ATX power connector as following CN1 pin information. 20-pin ATX power connector. 3.2 IDE’s LED, Keylock and Reset Button The following provides the pin information for IDE’s LED indicator, Keylock and Reset Button connections from CN3, CN5 and CN6.

  • Page 23: External Speaker

    CN5 : IDE LED Connector PIN NO. Description HDD Active# 3.3 External Speaker The HS-6300 has an on board buzzer. And it also provides the CN4 in allows user to connecting to the external speaker. CN7 : Speaker Connector PIN NO. Description...

  • Page 24: Pci E-Ide Drive Connector

    3.5 PCI E-IDE Drive Connector Two standard 40-pin header daisy-chain driver connectors provide as CN11 & CN12 with following pin assignment. Total four IDE drivers may connect. CN7(IDE 1)：Primary IDE Connector CN8(IDE 2)：Secondary IDE Connector CN7/CN8 : IDE Interface Connector PIN NO.

  • Page 25: Parallel Port Connector

    3.6 Parallel Port Connector A standard 26-pin flat cable driver connector provides as CN12 with following pin assignment for connection to parallel printer. CN12 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION STROBE DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5...

  • Page 26: The Floppy Disk Drivec

    3.7 The Floppy Disk Drive Connector A standard 34-pin header daisy-chain driver connector provides as CN13 with following pin assignment. Total two FDD drivers may connect. CN13 : FDD Connector PIN NO DESCRIPTION PIN NO DESCRIPTION GROUND REDUCE WRITE GROUND GROUND GROUND INDEX#...

  • Page 27: Serial Ports Connectors

    3.8 Serial Ports The HS-5010 offers two high speed NS16C550 compatible UARTs with Read/Receive 16byte FIFO serial ports. CN12 : Serial Port DB9 Connector PIN NO. DESCRIPTION Data Carrier Detect (DCD) Receive Data (RXD) Transmit Data (TXD) Data Terminal Ready (DTR) Ground (GND) Data Set Ready (DSR) Request To Send (RTS)

  • Page 28: Keyboard Connectors

    3.9 Keyboard Connector The HS-6300 offers two possibilities for keyboard connections to external PS/2 type keyboard at CN19, or an internal 5-pin header at CN2. CN2 : 5-pin Header Keyboard Connector PIN NO. Description Keyboard Clock Keyboard Data Ground CN19 : 6pin Mini-din Keyboard Connector PIN NO.

  • Page 29: Vga Connectors

    3.10 PS/2 Mouse 6-pin Mini Din Connector The HS-6300 provides an external PS/2 mouse connector at CN17 with following pin information. CN17 : PS/2 Mouse Connector PIN NO. Description MS Data Ground KBT1 3.11 VGA Connector The HS-6300 provides two possible connectives of VGA connections.
  • Page 30 3.12 Flat-Panel Connector The HS-6300 provides a 50-pin 2.0mm pitch header connector (CN9) for 3.3V Flat Panel connection with following pin assignment. +12V +12V +3V PVcc ENAVdd FPVee SHFCLK ENABKL...

  • Page 31: Ir Connector

    3.13 IR Connector The HS-6300 provides a 5-pin internal IR communication connector as following CN19 pin information. The CN19 provides for IrDA 1.0 specification application. CN22 : 5-pin IR Connector PIN NO. Description IRRX Ground IRTX...

  • Page 32: Fast Ethernet Connector

    3.14 Fast Ethernet Connector The Fast Ethernet controller provides with 32bit performance, PCI Bus master capability, and full compliance with IEEE 802.3 10/100 Based-T specifications. For 10/100 Base-T operation, please connect the network connection by plugging one end of the cable into the 9-pin RF-45 CN16 connector. CN16 : Ethernet Connector ( 9-pin RJ-45) PIN NO.

  • Page 33: Award Bios Setup

    Chapter-4 AWARD BIOS Setup The HS-6300 uses the Award PCI/ISA BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options which could be selected for end-user requirements.

  • Page 34: Main Menu

    4.1 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press ＜Enter＞...

  • Page 35: Standard Cmos Setup

    4.2 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, please set the HDD mode to LBA mode.

  • Page 36: Bios Features Setup

    4.3 BIOS Features Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot up sequence, keyboard operation, shadowing and security. ROM PCI/ISA BIOS (2A69KD2B) BIOS FEATURES SETUP AWARD SOFTWARE, INC.

  • Page 37: Chipset Features Setup

    4.4 Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses.

  • Page 38: Integrated Peripherals

    4.5 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship which is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks.

  • Page 39: Power Management Setup

    4.6 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. ROM PCI/ISA BIOS (2A69KD2B) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC.

This manual is also suitable for:

Hs-6300v

Table of Contents