Loewe Individual 55 Manual page 27

n
Individual 40-55
User guide
Initial installation
Setting options for the satellite system
(max. 4 satellites on DiSEqC multiswitch):
DiSEqC
multiple
Settings DiSEqC multiple switch
switch
With the refresh rate you determine how often a DiSEqC command is output. This is only
necessary in a cascaded system. Your system provider will bei able to tell you more about this.
Note: The newly selected parameter in each case must be confirmed with the
Repeat rate
Control voltage 13 / 18V
22kHz signal
Toneburst
Back with
5634 Select and adapt settings for the DiSEqC
OK Adopt settings.
Repeat rate The refresh rate determines how often a DiSEqC
command is output. A refresh is only necessary with
cascaded systems.
Control The control voltage controls the switching of the
voltage polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g., control of single LNBs via
DiSEqC multiswitch).
22kHz signal The 22 kHz signal controls the switching between
high and low band in the Band setting. The Position
setting controls the selection of the satellites in non-
DiSEqC capable components.
Toneburst The Toneburst controls the selection of the satellites
in non-DiSEqC but Toneburst capable components
with the Position and Option settings.
Conclude this step (for navigation refer to page 18).
Satellite
selection
5634 Mark Satellite 1 ... Satellite 4,
5634 Select satellite.
OK Adopt settings.
Conclude this step (for navigation refer to page 18).
none 1 2
off on
Band Position off
off Position Option
Proceed with
multiswitch.
Select satellites
Please select satellite 1 to satellite 4.
Satellite 1 Satellite 2 Satellite 3 Satellite 4
None ASTRA1 19,2°E Intelsat10-02 1°W
Türksat 42°E Eutelsat W2 16°E Atlantic Bird3 5°W
Hellas Sat2 39°E Hot Bird 13°E Telecom2C 5°W
Eutelsat W4 36°E Eurobird 9A 9°E Nilesat 7°W
Eurobird1 28,5°E Eutelsat W3A 7°E Atlantic Bird2 8°W
ASTRA2 28,2°E Sirius2/3 5°E Telecom2D 8°E
ASTRA3 23,5°E Thor2/3 0,8°W Atlantic Bird1 12,5°W
Back with Proceed with
- 27 -
LNC
frequencies
button.
OK
.
LNB frequencies
Please select the LNB frequencies for both High and Low Bands.
Note: The newly selected parameter in each case must be confirmed with the
ASTRA1 19,2°E low band 9750 MHz
ASTRA1 19,2°E high band 10600 MHz
Hot Bird 13°E low band 9750 MHz
Hot Bird 13°E high band 10600 MHz
Eutelsat W2 16°E low band 9750 MHz
Eutelsat W2 16°E high band 10600 MHz
Türksat 42°E low band 9750 MHz
Türksat 42°E high band 10600 MHz
Back with Proceed with
5634 Set LNB frequencies.
Normally, you do not need to change the values.
OK Adopt settings.
Conclude this step (for navigation refer to page 18).
(Proceed with Setting options for DVB-S reception
(continued) on page 30).
button.
OK
10000 MHz 10200 MHz 10600 MHz
10750 MHz 11000 MHz 11250 MHz
10000 MHz 10200 MHz 10600 MHz
10750 MHz 11000 MHz 11250 MHz
10000 MHz 10200 MHz 10600 MHz
10750 MHz 11000 MHz 11250 MHz
10000 MHz 10200 MHz 10600 MHz
10750 MHz 11000 MHz 11250 MHz