Software Selectable Line Interface Modes; Table 5: Line Interface Mode Settings - Connect Tech ComSync/104 User Manual

Table of Contents

Advertisement

Software Selectable Line Interface Modes

The Serial Line Interface utilizes Sipex devices SP507 (on Revision A and B cards) or SP508
(on Revision C and proceeding cards). Refer to the data sheet for these devices for all electrical
characteristics of the interface.
The Line Interface Mode is software selectable for each Channel. The following Modes are
available:
Pin#
26 Pin
25 pin
Signal
Header
D-Sub
TX+
2
TX-
3
RX+
6
RX-
5
DTR+
20
DTR-
14
RTS+
12
RTS-
7
CTS+
25
CTS-
9
DSR+
18
DSR-
11
DCD+
19
DCD-
15
RTxC+
17
RTxC-
8
[3]
SYNC+
21
[4]
[3]
SYNC-
22
[4]
[3]
TRxC+
23
[4]
[3]
TRxC-
4
[4]
GND
1, 13
Notes:
[1]
Tri-State
Hi-Z, resistance >= 10K Ω to GND
[2]
[3]
When Signal is an Output.
[4]
When Signal is an Input
120 Ω termination resistor is applied between the
[5]
(+) and (-) signals.

Table 5: Line Interface Mode Settings

Line Interface Mode Settings
I/O address offset 7: bits 0, 1, 2 are for Channel A & bits 3, 4, 5 are
000
001
010
14
V.11
V.11
V.11
2
V.11
V.11
V.11
[5]
[5]
16
V.11
V.11
V.11
[5]
[5]
3
V.11
V.11
V.11
[1]
23
V.11
V.11
20
V.11
V.10
V.11
19
V.11
V.11
V.11
4
V.11
V.11
V.11
13
V.11
V.11
V.11
5
V.11
V.11
V.11
[2]
22
V.11
V.11
6
V.11
V.10
V.11
[2]
[2]
[2]
10
8
V.10
V.10
V.10
[5]
[5]
9
V.11
V.11
V.11
[5]
[5]
17
V.11
V.11
V.11
V.11
V.11
V.11
11
V.11
V.11
V.11
V.11
V.11
V.11
24
V.11
V.11
V.11
V.11
V.11
V.11
12
[5]
[5]
V.11
V.11
V.11
V.11
V.11
V.11
15
[5]
[5]
V.11
V.11
V.11
1, 7
GND
GND
GND
(binary values)
for Channel B
011
100
101
[6]
V.11
V.11
V.35
[6]
V.11
V.35
V.11
[5]
[5]
[6]
[5]
V.11
V.35
V.11
[5]
[5]
[6]
[5]
V.11
V.35
V.11
[1]
V.11
V.11
V.11
V.28
V.11
[1]
V.11
V.11
V.11
V.28
V.11
[2]
V.11
V.11
V.11
V.28
V.11
[2]
V.11
V.11
V.11
V.28
V.11
[2]
[2]
[2]
V.10
V.28
V.10
[5]
[5]
[6]
[5]
V.11
V.35
V.11
[5]
[5]
[6]
[5]
V.11
V.35
V.11
[1]
V.11
V.11
[2]
V.11
V.11
V.11
V.28
V.11
V.11
V.28
V.11
[6]
V.11
V.35
V.11
[5]
[5]
[6
[5]
V.11
V.35
] V.11
[6]
V.11
V.35
V.11
[5]
[5]
[6]
[5]
V.11
V.35
V.11
GND
GND
GND
[6]
V.35 Termination Network is
applied between the (+) and (-)
signals.
V.10 = RS-423
V.11 = RS-422
V.28 = RS-232
V.35 = V.35
110
111
[1]
[1]
[1]
V.28
[2]
[2]
[2]
V.28
[1]
[1]
[1]
V.28
[1]
[1]
[1]
V.28
[2]
[2]
[2]
V.28
[2]
[2]
[2]
V.28
[2]
[2]
[2]
V.28
[2]
[2]
[2]
V.28
[1]
[1]
[2]
[2]
[1]
V.28
[2]
V.28
[1]
[1]
[2]
[1]
[1]
V.28
[1]
V.28
GND
GND

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ComSync/104 and is the answer not in the manual?

Table of Contents