Table of Contents
Advertisement
INTERCOM MIC Cable
1.
Balance (HEAD SET menu UNBAL: OFF)
2.
Unbalance (HEAD SET menu UNBAL: ON)
1-1-3.
Connectors and Cables
Connection made with the connectors during installation or
service, should be made with the connectors/complete cable
assemblies specified in the following list, or equivalent parts.
Connector Name
Connectors and Cables
CCU
CCFN-25/50/100 cable
(manufactured by
or single-mode optical fiber cable (Terminal
NEUTRIK)
shaped: PC (Physical Contact) polishing or
Advanced PC etc. PC polishing compatible
cable, Wavelength: 1310 nm compliant)
CCU
FUW.3K.93C.TLMC96 manufactured by
(manufactured by
LEMO
LEMO)
PROMPTER/
Plug, BNC (Part No.: 1-564-742-11)
GENLOCK
or B-B Cable assembly (1.5 m optional)
TEST OUT
(BNC type)
SDI IN
Plug, BNC (Part No.: 1-569-370-12)
SDI OUT
or 5C-FB coaxial cable/ Recommendation
(BNC type)
manufactured by Fujikura
AUDIO 1/2 IN
XLR 3-pin, Male (Part No.: 1-508-084-00)
(XLR 3-pin, Female)
or ITT Cannon XLR-3-12C equivalent
INTERCOM
XLR 5-pin, Male (Part No.: 1-508-370-11)
(XLR 5-pin, Female)
or ITT Cannon XLR-5-12C equivalent
DC IN
XLR 4-pin, Female (Part No.: 1-508-362-00)
(XLR 4-pin, Male)
or ITT Cannon XLR-4-11C equivalent
or DC cable CCDD-X2 (2 m)
DC OUT
Plug 4-pin, Male (Part No.: 1-566-425-11)
(4-pin, Female)
or HIROSE HR10A-7P-4P equivalent
*1:
If using a cable of length different from a standard product, contact your local Sony Sales Office/Service Center.
*2:
The pin 8 of CCA-5 cable is GND (ground).
*3:
The pin 8 of REMOTE cable is not GND (ground).
*4:
Use of REMOTE cable enables to monitor video signals. (The pin 8 is available for the video signal line.) The down-converted SD
signal is output.
HXC-FB75H/HXC-FB75KC
G
X
INTERCOM
Y
MIC
X
INTERCOM
Y
MIC
Continued
Connector Name
Connectors and Cables
EARPHONE
Plug, Mini, Stereo
LENS
Connector 12-pin, Male (Part No.:
(12-pin, Female)
1-564-360-11)
or HIROSE HR10-10PA-12P equivalent
REMOTE
•
Plug 8-pin, Male (Part No.:
(8-pin, Female)
1-766-848-11)
or CCA-5 cable assembly (CCA-5-3 (3
m)/CCA-5-10 (10 m)) (optional)
•
REMOTE cable (Part No.:
1-783-372-11)
(Supplied with RM-B170/B750, 10
m)
TRUNK
D-sub 9-pin, Male (Part No.: 1-568-182-11)
(D-sub 9-pin, Fe-
or JAE DE-9PF-N equivalent (Available
male)
shell: JAE DE-C1-J6-R equivalent)
VF (Round, 20P)
Connect the cable of the optional/ supplied
(HXC-FB75KC) viewfinder (HDVF series).
1-1-4.
Note in Connecting Single-mode
Optical Fiber Cable
• When you use only single-mode optical fiber cable to
connect the HXCU-FB70 to this unit, configure the optical
output setting in HXCU-FB70. (Refer to the Operating
Instructions of HXCU-FB70.)
• Connect the single-mode optical fiber cable as shown below
so that connecting destinations cross (A to B, B to A)
between this unit and the HXCU-FB70.
Single-mode optical fiber
HXCU-FB70
cable (pair)
A
B
• The single fiber cable used for the connection must use the
cable that the following specifications are complied with.
- Terminal shaped: PC (Physical Contact) polishing or
Advanced PC etc. PC polishing compatible cable
- Wavelength: 1310 nm compliant
*1*2
*1*3*4
This unit
A
B
1-6
Advertisement
Table of Contents
