Samsung EHS AE050RXYDEG/EU Manual page 41

5. Unit installation
• General area
While Air-Water Heat Pump is running in heating mode, Ice can begin accumulate on the surface of condenser .
To prevent Ice from growing, system go into De-frost mode and then Ice on the surface changes to water .
Dropped water from condenser shall be eliminated through running drain holes to prevent Ice growing at low temperature .
f In case there is not enough space for drainage out of the unit, additional drain
Mono HT Quiet
Model
AE080/120/140BXYD**
Drain hole Φ20
WARNING
Drain
hole
shape
Drain plug x 1ea
1 . Prepare a water drainage channel around the foundation, to drain waste water from around the unit .
2 . If the water drainage of the unit is not easy, please build up the unit on a foundation
1 Prepare a water drainage channel around the foundation,
3 . If you install the unit on a frame, please install a waterproof plate within 150 mm of
to drain waste water from around the unit.
4 . When installing the unit in a place frequently exposed to snow, pay special attention
2 If the water drainage from the unit is inadequate, please raise the unit on construction
5 . If you install the unit on a building frame, please install a waterproof plate (field
concrete blocks, etc. (the height of the construction should be at least 150 mm).
3 If you install the unit on a frame, please install a slanted waterproof plate within 150 mm
of the underside of the unit to prevent water from plashing against the bottom plate from
below.
4 When installing the unit in a place frequently exposed to snow, pay special attention to elevate the foundation as high
as the average snow height plus the additional required 150mm.
5 If you install the unit on a wall support bracket, please install drainage pipework. In order to avoid the drain water
from dripping on the floor potentially creating a slippery surface or an ice layer under freezing conditions. (See figure)
※ Please securely mount the outdoor unit before connecting the water piping.
Installer reference guide / Mono tank integrated type
Drain hole Φ20
Drain plug x 1ea
212.5mm
Drain work Drain work
• General area
While Air-Water Heat Pump is running in heating mode, Ice can begin accumulate on the surface of condenser .
To prevent Ice from growing, system go into De-frost mode and then Ice on the surface changes to water .
Dropped water from condenser shall be eliminated through running drain holes to prevent Ice growing at low temperature .
f In case there is not enough space for drainage out of the unit, additional drain
f f
works are required . Follow the description as below works are required . Follow the description as below
- Make space more than 100mm between the bottom of the outdoor unit and - Make space more than 100mm between the bottom of the outdoor unit and
the ground for installation of the drain hose . the ground for installation of the drain hose .
- Insert the drain plug into the hole on the bottom of the outdoor unit . - Insert the drain plug into the hole on the bottom of the outdoor unit .
- Connect the drain hose to the drain plug . - Connect the drain hose to the drain plug .
- Make sure dusts or small branches should not go into the drain hose . - Make sure dusts or small branches should not go into the drain hose .
• If drain work is not enough, it can lead to system performance degration and system damages . • If drain work is not enough, it can lead to system performance degration and system damages .
WARNING
Drain hole Ø20
Air discharge side
13mm
Drain plug x 1ea
1 . Prepare a water drainage channel around the foundation, to drain waste water from around the unit .
2 . If the water drainage of the unit is not easy, please build up the unit on a foundation
of concrete blocks, etc . (the height of the foundation should be maximum 150 mm) . of concrete blocks, etc . (the height of the foundation should be maximum 150 mm) .
3 . If you install the unit on a frame, please install a waterproof plate within 150 mm of
the underside of the unit in order to prevent the invasion of water from the lower the underside of the unit in order to prevent the invasion of water from the lower
direction . direction .
4 . When installing the unit in a place frequently exposed to snow, pay special attention
to elevate the foundation as high as possible . to elevate the foundation as high as possible .
5 . If you install the unit on a building frame, please install a waterproof plate (field
supply) (within 150mm of the underside of the unit) in order to avoid the drain supply) (within 150mm of the underside of the unit) in order to avoid the drain
water dripping . (See figure) water dripping . (See figure)
13mm
AE050RXYDEG
Drain hole Φ20 234.8mm
Drain hole Ø20
Air discharge side
Air discharge side Air discharge side
30mm
30 mm
Drain plug x 1ea
Drain plug x 1ea
ENGLISH-21 ENGLISH-21
Mono
AE080/120/160RXYD**
815.9mm
Drain hole Φ20 x 4 ea
521.5mm
303.9mm
822.2mm
Air discharge side
13mm
30 mm
Drain plug x 1ea Drain cap x 3ea
40