Table of Contents
Advertisement
WIRE CONNECTION TERMINAL BLOCK
1 2
-
:
These two terminals are prepared for connecting the incoming telephone
TELEPHONE
line. The system connects the house telephone set to the telephone line in
LINE
normal condition, and it picks up the line for the communicator or the auto-
dialer whenever it goes into action.
3
:
This is the earth point of the system. This terminal should be connected to a
EARTH
nearest solid electrical earth point such as a cold water pipe or earth stake in
order for it to provide protection against possible lightning interference. Use
14 gauge wire or lager for this connection.
compromises safety!
4 5
-
:
These two terminals are prepared for the connection of the house telephone
TELEPHONE
set which is connected to the telephone line in normal condition. The house
SET
telephone set will be automatically disconnected from the telephone line
whenever the communicator or the auto-dialer goes into action.
6 7
-
:
Power input terminals of the system. A 12 16VDC/1.5A rating power source
12-16VDC
is recommended. Terminal 6 is ( ), and 7 is (+). Power adaptor, AP-960 is
INPUT
recommended. It gives 12VDC at rated current (1.5A) and 15 16VDC at
POWER
standby condition, which ensures that the back-up battery is properly
charged.
JUMPER AND SWITCH ON CIRCUIT BOARD
DAP JUMPER
:
DAP stands for Direct Access to Programming. This jumper is prepared for
setting the system into programming mode in case that the personal master
code is forgotten. See page 16 for details.
TAMPER
:
The tamper switch is pre-wired to zone 8 internally. Always keep zone T
SWITCH
(eg. zone 8) programmed as a 24-hour protection zone.
The tamper switch is Normal Closed (N.C.) when the circuit module is
secured in the box; and it is open circuit and triggers the alarm when the
cover is removed from the box.
D.T. JUMPER
:
Two Dial Tones are commonly used at today's telephone central office, the
continuous dial tone and the cadenced tone comprising the repeated
sequence of ON and OFF of the tone.
It is important to make the correct setting in your system to match the dial
tone used at the telephone central office in your city. The D.T. JUMPER
(Dial Tone Selection Jumper) can be found at the right hand side of the
main circuit board. Put jumper on:
1) CONT.
for continuous dial tone
2) CAD.
for cadenced dial tone
Incorrect setting of the D.T. JUMPER may cause malfunction to the "Dial
Tone & Line Fault Detects", or the "Ring Detect To Pickup Telephone Line
On Remote Access" that you programmed.
12
TERMINAL DEFINITIONS AND DESCRIPTIONS
Failure to earth the unit
-
-
-
(Factory put jumper on 1)
HA-266
CHANGE AND DELETE
RECORD THE ALARM REPORTING MESSAGE FOR AUTO-DIALER
The recording message for alarm reporting can be changed at any time you like to better reflect
the situation of your alarm system.
The procedures for message recording are as follows:
1) Enter your [MASTER CODE] and validate by [ ] [ ]
MASTER CODE
!
The
PROGRAM
light comes ON.
!
System is in programming mode.
2) Press [RECORD] and validate by [#] key on the panel
RECORD
#
!
The
RECORD
light comes ON. It will last for 20 seconds
!
The microphone is equipped on the panel.
3) When the
RECORD
light is ON, speak to the microphone with your face about 30cm (1ft)
from it. The light will be OFF when the 20 seconds expired and your message is stored.
4) Recording can be repeated as many times as you like until the message is in your
satisfaction. The newly recorded message replaces the old one.
Repeat procedures 2 and 3 for recording repeats.
5) Exit the programming mode by pushing [ ] [ ].
!
System is back to operation mode.
6) Try to test and listen to the newly recorded message by initiating auto dialer telephone test
with one of the telephone numbers.
Testing can be made easier if you possess a portable telephone and a portable AM/FM
radio. For testing purposes, you can temporarily program your portable telephone's number
in one of the locations
(61-63)
in the auto-dialer section, and switch the AM/FM radio on to
play softly and put it about two meters
monitor the recorded message and the listen-in function without bothering anyone.
HA-266
(6 feet)
away from the dialer. This way you can
65
Advertisement
Table of Contents
