Table of Contents
Advertisement
Quick Links
An Innovative Product
Developed By:
PROTECT - ON
SYSTEMS LTD.
www.protect-on.com
R
SINCE 1979
ADVANCED ELECTRONICS INDUSTRY
MANUAL NUMBER: HA-266 Rev. 0
6
-ZONE ALARM CONTROL PANEL
WITH AUTO-DIALER AND COMMUNICATOR
HA-266
FOR HOME AND OFFICE PROTECTIONS
OWNER'S MANUAL
Programming And Operation
R
SINCE 1979
Advertisement
Table of Contents
Related Manuals for AEI HA-266
Summary of Contents for AEI HA-266
- Page 1 -ZONE ALARM CONTROL PANEL WITH AUTO-DIALER AND COMMUNICATOR HA-266 FOR HOME AND OFFICE PROTECTIONS OWNER'S MANUAL Programming And Operation An Innovative Product Developed By: SINCE 1979 SINCE 1979 PROTECT - ON ADVANCED ELECTRONICS INDUSTRY SYSTEMS LTD. www.protect-on.com MANUAL NUMBER: HA-266 Rev. 0...
- Page 2 The HA-266 has been prepared with the facility of connecting optional key switches for arm- Thank you for choosing the HA-266 Alarm Control Panel to protect you and your property. Your disarm controls. If your system is equipped with the optional key switch, you can make arm- system is one of the most powerful and advanced alarm systems on the market today, designed disarm controls from the key switch as like from the control console.
-
Page 3: Table Of Contents
Dialing to an auto-pager station from the auto-dialer ......24 Sending an alarm report to your auto-pager from communicator....25 HA-266 HA-266... - Page 4 OPENING THE CABINET FOR SERVICE ......... 51 HA-266...
-
Page 5: Introduction
1 BEEP , system is in disarmed state. HA-266 is a compact Alarm Control Panel with 6 hardware protection zones and 2 software Enter [USER CODE 1] and validate by [#] zones for panic and duress alarms, which is designed for home and office protections using the latest security concepts. -
Page 6: The System Control Console And Its Indicators
REMOTE CONTROL OF THE SYSTEM BY TELEPHONE THE SYSTEM CONTROL CONSOLE AND ITS INDICATORS (1) THE MASTER CONTROL CONSOLE The HA-266 has been designed to allow the owner to telephone the system remotely (See Program Location 83 for details) to check its arm-disarm status, to make arm-disarm control or to request the communicator for a current status report sending to the monitor station or to the owner's pocket pager. -
Page 7: The Led Light Indicators
Alarm system is enabled during the listen-in period. FLASHING TWICE Dialing for duress The system is in telephone line after the duress fault testing code is entered Voice RECORDING No recording, or recording is in the recording progress time is expired HA-266 HA-266... -
Page 8: The Sound Indicators
5) On NON-BACKUP reporting mode, an acknowledgement signal must be received from each telephone in the group of 4 (if 4 numbers are stored) before the current event is considered to be reported and closed. HA-266 HA-266... -
Page 9: Terminal Definitions And Descriptions
GREY ( ) GROUND 3) Exit the programming mode by pushing [ ] [ ] BLACK +12V OUTPUT AT NORMAL CONDITION System is back to operation mode. 12 16V INPUT POWER RING TELEPHONE SET EARTH RING TELEPHONE LINE HA-266 HA-266... -
Page 10: Unpluggable Wire Harness
[0 or 1] required, enter the new [TELEPHONE NUMBER] and validate by [#]. Alarm memory is The alarm memory LEDs are off (The zone LEDs on 2nd Touch cleared the control console) System keeps in The system is ready for re-arming TELEPHONE LOCATION TELEPHONE NUMBER disarmed mode HA-266 HA-266... - Page 11 The new user code is accepted, it can be 2 to 5 digits. If the programming is rejected, 5 beeps will be generated. Try again. 3) Exit the programming mode by pushing [ ] [ ] System is back to operation mode. HA-266 HA-266...
-
Page 12: Wire Connection Terminal Block
2) CAD. for cadenced dial tone Incorrect setting of the D.T. JUMPER may cause malfunction to the "Dial Tone & Line Fault Detects", or the "Ring Detect To Pickup Telephone Line On Remote Access" that you programmed. HA-266 HA-266... -
Page 13: Back-Up Battery
Battery Connection Enter your [USER CODE], press [ ], Enter the [TELEPHONE LOCATION], validate by [#] Wires HA-266 Cabinet To initiate main monitor station test --- COMMUNICATOR TELEPHONE NO.1 USER CODE To initiate backup monitor station test --- COMMUNICATOR TELEPHONE NO.2... -
Page 14: Factory Settings
Dial-tone and line fault detects Enabled ....... . Code=1 HA-266 HA-266... -
Page 15: Programming The Panel
The counting of the periodic test starts at the time when the system is power-up (when AC or DC power is firstly connected) The time counting of the periodic test is not affected by the manual battery test. HA-266 HA-266... -
Page 16: Use The Dap Jumper Directly Access To Programming Mode
There will be no indication of an alarm condition on the control console. The system will be turned if it is in ARMED or in ALARM MEMORY condition. The system will keep itself in condition if it is HA-266 HA-266... -
Page 17: Recording The Client Code
When a new code is entered into the location, the old code will be replaced. To invalid a code, just key-in the specific location number followed immediately by the [#] key without program data. HA-266 HA-266... -
Page 18: The Duress Code
BEFORE KEYING - IN THE DURESS CODE AFTER KEYING - IN THE DURESS CODE System was armed System is disarmed and starts dialing for reporting alarm System was disarmed System is still disarmed and starts dialing for reporting alarm. HA-266 HA-266... -
Page 19: Configuration Of The Protection Zones
LED will be ON showing that it is a faulty zone. CODE 3--LOOP RESPONSE TIME Loop response time is the time required to trigger a protection Zone. 0 -- 25 mS 2 -- 500 mS (DEFAULT FOR ALL ZONES) 1 -- 250 mS 3 -- 750 mS HA-266 HA-266... -
Page 20: Setting The Exit Delay Time
The system will activate its timing alarm output (terminal 9) to generate short beeps when the system is armed or disarmed: 1 BEEP-----DISARMED 2 BEEPS-----ARMED SIREN DURATION (DEFAULT: 300 seconds) 2 999 SECONDS The siren duration can be set from 2 to 999 seconds HA-266 HA-266...