Advertisement
INITIATE A DYNAMIC BATTERY TEST
The system tests the back-up battery once every 24 hours. The owner can initiate a dynamic
battery test at any time with the following codes while the system is in diarmed condition.
USER CODE
4
!
Manually initiated testing does not affect the periodic battery test.
!
The test takes 5 seconds to 2 minutes depending on the condition of the battery.
!
Manually battery test is usually required after installation of a new back-up battery.
INITIATE A DYNAMIC TEST OF THE OUTPUT RELAYS
It is necessary to test the output relays periodically to ensure that they work normally. The owner
can key-in the following command to initiate the test while the system is in disarmed condition.
USER CODE
5
!
Both timing and latch output relays operate for 5 seconds to energize the siren and strobe
light.
!
If the siren or the strobe does not work normally, check the wiring and the device immediately.
!
Suggest to make test monthly.
OPEN THE CABINET FOR SERVICE
The alarm control panel is protected by a built-in tamper switch. Opening of the cabinet will
trigger the tamper switch to give alarm.
The whole system including the tamper switch can be disarmed by setting it into programming
mode with the master code.
MASTER CODE
!
After the system is in programming mode, the tamper switch is disabled. The cabinet can be
opened for service without triggering an alarm.
!
Don't forget to press
to set system back to normal operation after service.
28
HA-263D (OPERATION)
#
#
8-ZONE ALARM CONTROL PANEL
FOR HOME AND OFFICE PROTECTIONS
HA-263
HA-263K
HA-263D
OWNER'S MANUAL
Installation And Operation
Version 01/08
R
SINCE 1979
Advertisement
Related Manuals for AEI HA-263K
Summary of Contents for AEI HA-263K
- Page 1 INITIATE A DYNAMIC TEST OF THE OUTPUT RELAYS It is necessary to test the output relays periodically to ensure that they work normally. The owner can key-in the following command to initiate the test while the system is in disarmed condition. HA-263K USER CODE HA-263D Both timing and latch output relays operate for 5 seconds to energize the siren and strobe light.
-
Page 2: Connection Terminals
The system resumes to normal operation 5 seconds after the beep if it is not prolonged. The system does not allow to arm during faulty zone checking and the keypad is temporarily AEI PROTECT - ON SYSTEMS LTD. disabled. www.protect-on.com... -
Page 3: Table Of Contents
TABLE OF CONTENTS HA-263D (OPERATION) User Code 3 can make bypass to all protection zones in all partitions including the zones in NTRODUCTION ..........................4 the common partition. CONNECTION TERMINALS.......................5 Make sure the system is in disarmed state with no alarm memory existing. THE BACK-UP BATTERY........................9 Enter the [User Code], press [BYPASS], Key-in the [ZONE NUMBER(S)] that you wish to THE PROGRAMMING JUMPERS ....................10... -
Page 4: Operation
The bypassed zone LEDs flash all the time to indicate that the zones are not protected The HA-263 is offered with two versions, the HA-263K is arm-disarm controlled with keyswitch for simple operation. The HA-263D comes with a digital keypad for arm-disarm control with user System will arm after exit delay expired. -
Page 5: Ha-263D
OPERATION CONNECTION TERMINALS The User Code that stated in the description of operation stands for the code for arm-disarm control of partition 1, partition 2 or the whole system. User Code 1 for Partition 1 User Code 2 for Partition 2 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 User Code 3 for the Whole System N.O. - Page 6 CONNECTION TERMINALS HA-263D (START THE PROGRAMMING) B) CONNECTION OF THE POWER CORD TO THE AC POWER TERMINAL REFRESH THE SYSTEM TO ITS DEFAULT VALUES (Location 21) BLOCK (For "T" Version only) The "T" Version alarm control panel comes with a built-in power transformer. Its LOCATION ENTRY OF CODE VALIDATION...
- Page 7 RESPONSE TIME system is ready to arm. The zone response time is fixed on 500mS for HA-263K, which is the value suitable for most of c) If continuously hold any one of the keyswitch in contact for more than 5 the sensors' alarm output.
- Page 8 1 TO 7 THE HA-263K HOME The standard HA-263K is supplied with only one key- switch for arm-disarm control of the partition 1 and 2 in Home mode is available only for arming the system via User Code 3 but not for partitional operation combined operation.
- Page 9 START THE PROGRAMMING THE BACK-UP BATTERY After the system is set in programming mode, you can program the system with your desired The back-up battery is not supplied. It is required to purchase separately. values of the available options. You can make the programming for all the options continuously or just select the option(s) that you require.
-
Page 10: Feature Programming
KS (Key Switch) --- Always put jumper on KS position for the system using Key-Switch for arm-disarm control (HA-263K). Once the jumper is SET SYSTEM IN PROGRAMMING MODE on KS position, all the values programmed with the Digital Keypad will... -
Page 11: Operation
HA-263D (THE DIGITAL CONTROL KEYPAD) THE PROGRAMMING JUMPERS 4) AUDIBLE BEEPS Battery LED There are 3 jumpers for ON-OFF selection of Entry Beep, Exit Beep and Warning Beep OFF --- Battery normal independently. ON --- Battery low a) Entry Beep --- Beeps during the entry delay period. -
Page 12: Arm The System
OPERATION HA-263D (THE DIGITAL CONTROL KEYPAD) Control Key Buttons SYSTEM STANDBY There are 14 buttons for code entry and function confirmation: The system standby period begins right after power-up or set it manually by holding the Numeric Buttons, 1 0 --- For code entry keyswitch in contact for more than 5 seconds during the system in disarmed mode. -
Page 13: Clear The Alarm Memory
THE ZONE STATUS LEDS FOR PARTITION 1 AND 2 EVENTS INDICATIONS HA-263K owner requires no study of this section. All information is for HA-263D only. System disarmed HA-263D is the version comes with a digital control keypad which allows owner to program two independent user codes for partition 1, 2 and the common partition;... -
Page 14: Open The Cabinet For Service
OPEN THE CABINET FOR SERVICE SUMMARY OF THE VISUAL AND AUDIBLE NOTIFICATIONS THE AUDIBLE NOTIFICATIONS The HA-263K is protected by a built-in tamper switch. Opening of the cabinet will trigger the tamper switch to give alarm. EVENTS NOTIFICATIONS If opening of the cabinet for service is required, it is necessary to set the system to standby mode by holding the keyswitch in contact for 5 seconds (ignore the 2 arming beeps).