Table of Contents
Advertisement
spouts. A series of rinses is performed automatically to re-
move all the scale residues inside the coffee machine;
After about 25 minutes, descaling stops;
9. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (fig. 4):
the appliance is now ready to rinse with fresh water. Empty
the container used to collect the descaler solution. Extract
the water tank, empty, rinse under running water, fill
with fresh water up to the MAX level and put back in the
appliance;
10. "POSITION 2l CONTAINER" "OK TO START RINSING": Place
the container used to collect the descaler solution empty
under the coffee spouts and hot water spout (fig. 9) and
press
;
11. Hot water is delivered first from the coffee spouts, then
from the hot water spout and "RINSING UNDERWAY" is
displayed;
12. When the water in the tank has run out, empty the con-
tainer used to collect the rinsing water;
13. (If the filter is installed) "INSERT FILTER INTO ITS HOUSING"
(fig. 36). Press "
Replace the water softener filter if removed previously;
14. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (fig. 4): Fill
the tank up to the MAX level with fresh water;
15. "INSERT WATER TANK" (fig. 5): Put the water tank back in
the appliance;
16. "POSITION 2l CONTAINER" "OK TO START RINSING": Place
the container used to collect the descaler solution empty
under the hot water spout (fig. 9) and press
17. Hot water is delivered from the hot water/steam spout and
"RINSING UNDERWAY" "PLEASE WAIT" is displayed;
18. "EMPTY DRIP TRAY" (fig. 22): At the end of the second
rinse, remove, empty and replace the drip tray (A15) and
grounds container (A11) and press
19. "DESCALE COMPLETE": press
20. "FILL TANK WITH FRESH WATER": empty the container
used to collect the rinse water, remove the water tank and
" and extract the water tank.
36
;
;
fill with fresh water up to the MAX level, then put back in
the appliance.
The descaling cycle is now complete.
Please note!
•
If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
•
After descaling, it is normal for the grounds container
(A11) to contain water.
•
If the water tank has not been filled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been complete-
ly eliminated from the machine's internal circuits. Before
starting rinsing, remember to empty the drip tray;
•
The appliance may request descaling cycles at very short
intervals. This is normal and due to the appliance's ad-
vanced control system.
14.
SETTING WATER HARDNESS
The "DESCALING NEEDED PRESS OK TO START (~45MIN)
" message is displayed after a period of time established
according to water hardness.
The machine is set by default for a hardness value of "4". The
machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
14.1 Measuring water hardness
1. Remove the TOTAL HARDNESS TEST indicator paper (D1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
Indicator paper
14.2 Setting water hardness
1. Access the menu as described in section "6.1 Access the
settings menu";
2. Press "WATER HARDNESS";
17
Water hardness
Level 1 - soft water
Level 2 - slightly hard
water
Level 3 - hard water
Level 4 - very hard water
Advertisement
Table of Contents
Troubleshooting
