Quadratec QuadraTop Adventure Top S Manual
Compelete soft top kit with flip back sunroof for 2007-2018 2 door jeep wrangler jk
Hide thumbs
Also See for QuadraTop Adventure Top S:
- Installation manual (21 pages) ,
- Manual (16 pages) ,
- Manual (15 pages)
Advertisement
Quick Links
QuadraTop
With Flip Back Sunroof
This Replacement Top kit is designed to fit on your 2 Dr Jeep® Wrangler when
the original soft top or hard top has been completely removed. Before begin-
NOTICE
ning your installation of this product, you will need to remove your existing soft
top fabric, hardware or Hard top.
Loss of vehicle control involves risk of death or serious injury, particularly to
parts of your body not restrained within vehicle. This product is intended for
weather protection only and should not be relied upon to contain occupants
in the event of an accident or to protect from either ground contact or falling
objects. To reduce risk of accident or injury:
•
WARNING
•
•
•
RISK OF EYE INJURY. Safety glasses should be worn at all times while insta-
CAUTION
lling or maintaining this product.
PART LIST:
TOP DECK/HEADER ASSEMBLY
DRIVER SIDE QUARTER WINDOW
PASSENGER SIDE QUARTER WINDOW
REAR WINDOW
DRIVER SIDE OVER DOOR BOW
PASSENGER SIDE OVER DOOR BOW
CENTER BOW ASSEMBLY
DRIVER'S SIDE DOOR SURROUND
PASSENGER SIDE DOOR SURROUND
DOOR SURROUND KNOBS
ROLL BAR BOW MOUNT BRACKETS
Adventure Top S
®
for 2007-2018
2 Door Jeep
Wrangler JK
®
Item
11113.1435
#
ALWAYS WEAR SEATBELTS
Always keep head, arms & body parts within vehicle.
Fully secure or stow the soft top before driving according to instructions.
Never try to latch or fold soft top while driving. Do not use if damaged or
worn.
Read and follow all instructions & warnings accompanying this product, in
your vehicle owner's manual and Off Road Driving Supplement.
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 4
QTY 2
REQUIRED TOOLS:
SAFETY GLASSES
PHILLIPS SCREW DRIVER
FLAT HEAD SCREW DRIVER
T-30 TORX DRIVER
PLIERS
Advertisement
Related Manuals for Quadratec QuadraTop Adventure Top S
Summary of Contents for Quadratec QuadraTop Adventure Top S
- Page 1 QuadraTop Adventure Top S ® With Flip Back Sunroof for 2007-2018 2 Door Jeep Wrangler JK ® Item 11113.1435 This Replacement Top kit is designed to fit on your 2 Dr Jeep® Wrangler when the original soft top or hard top has been completely removed. Before begin- NOTICE ning your installation of this product, you will need to remove your existing soft top fabric, hardware or Hard top.
- Page 2 CAUTION you don’t follow instructions. Careful attention is required to this instruction or operation but does genera- lly not relate to personal injury. Damage to your Quadratec® product or other NOTICE property may result if you don’t follow instructions. Before you begin Installation: We are excited that you have chosen the Adventure Top.
- Page 3 Next, secure the over door bow to the Header leg with the attached set screw (Fig 6).Slide the bow sleeve over the knuckles as shown in Fig 7. Repeat this procedure on the opposite side. Step 2: Install Bow Mount Brackets to Roll Bar Locate the (2) bow mounting brackets and (4) Allen head pivot bracket bolts shown in FIG 8.
- Page 4 Step 3: Pillar and Over Door Surround Assembly and Install Locate the driver’s side Rear over door assembly and the driver’s side Pillar assembly shown in FIG12. On the driver’s side rear over door assembly, there is a screw, installed for shipping (Fig 13). Remove this screw and set aside Driver Side Over Door Assembly Driver Side...
- Page 5 FIG 20 FIG 21 FIG 22 FIG 23 Install Door Surrounds to Jeep: Continued Next, Insert this pin into the body tub as shown in FIGs 20 & 21. After inserting the pin, locate the upper portion of the door surround “C” attachment and push onto roll bar (FIGs 22& 23). Make sure the front seal is snug against the FIG 24 windshield seal as shown in FIG 24.
- Page 6 Step 4: Install Center Bow to the Vehicle: Continued With a friend, place the bow assembly over the roll bar and line up the assembly to the upper bow mount bracket (Fig 29) that was installed in step 2. The center bow should be towards the rear of the vehicle as shown in Fig 28.Line up the Quick release knuckle on the bow assembly with the upper bow mount bracket attachment and attach each side of the center bow assembly to the bracket (Figs 30, 31 &...
- Page 7 Step 5: Installing the Header/Deck Fabric Fabric to the Center Bow: Continued Locate the center bow webbing attached to the center bow and the spring assembly that is attached to the top deck. Figs 39 & 40.Attach the spring end to the webbing as shown in figs 41 and 42. NOTE: Fig 42 shows the spring end coming all the way through the web strap.
- Page 8 Step 6 Continued: Installing the Top Deck to the Jeep® With the fabric installed on the header and draped over the back of the vehicle, go to the rear corner of the Top deck and locate the rear corner straps. Thread the straps down and under the seat belt mount as shown in FIGs 46 &...
- Page 9 Step 7: Installing the Quarter and Rear Windows to the Top Deck Continued: Locate the rear window and line up and slide the rear window into the “C” Channel located at the top of the rear portion of the top deck (FIGs 53, 54 & 55).Once both quarter windows and rear window are secured to the top deck, line up the driver’s side rear zipper on the Quarter window to the zipper on the rear window and zip it down a few inches (FIG 56).
- Page 10 Step 8: Installing the Top to the Jeep Body Continued Go inside the Jeep and locate the long center bow flap. Wrap this bow flap tightly around the center bow and secure it with the hook and loop fastener (FIGs 62 & 63). you can now reach through the rear zipper on each side and tighten the corner straps.
- Page 11 Step 9 Continued: Installing the Tailgate Bar and Rear Window to the body of the Jeep Once the Tailgate bar in secure, lower zippers on both sides of the rear curtain (FIG 70) and then secure the rear zipper cover flap as shown in Figs 71 & 72. FIG 70 FIG 71 FIG 72...
- Page 12 Zippers: Keeping the zipper cleaned and “polished” out using the window polish listed lubricated with a silicone lubricant (see Page on page 15 (Available at Quadratec.com). 15) will help prevent damage and keep the Water/Fabric: In the event of seeping zippers in a smooth working condition.
- Page 13 Quadratec, Inc. 1028 der shall, upon Quadratec inspection and Saunders Lane, West Chester, PA 19380. at Quadratec’s option, be either repair or replacement of product or parts (new or This Limited Warranty is the only warranty refurbished) covered under this Limited Warranty.