Advertisement
Quick Links
QuadraTop
With Flip Back Sunroof
This Replacement Top kit is designed to fit on your 2 Dr Jeep® Wrangler when
the original soft top or hard top has been completely removed. Before begin-
NOTICE
ning your installation of this product, you will need to remove your existing soft
top fabric, hardware or Hard top.
Loss of vehicle control involves risk of death or serious injury, particularly to
parts of your body not restrained within vehicle. This product is intended for
weather protection only and should not be relied upon to contain occupants
in the event of an accident or to protect from either ground contact or falling
objects. To reduce risk of accident or injury:
•
WARNING
•
•
•
RISK OF EYE INJURY. Safety glasses should be worn at all times while insta-
CAUTION
lling or maintaining this product.
PART LIST:
TOP DECK/HEADER ASSEMBLY
DRIVER SIDE QUARTER WINDOW
PASSENGER SIDE QUARTER WINDOW
REAR WINDOW
DRIVER SIDE OVER DOOR BOW
PASSENGER SIDE OVER DOOR BOW
CENTER BOW ASSEMBLY
DRIVER'S SIDE DOOR SURROUND
PASSENGER SIDE DOOR SURROUND
DOOR SURROUND KNOBS
ROLL BAR BOW MOUNT BRACKETS
Adventure Top S
®
for 2007-2018
2 Door Jeep
Item
11113.1435
#
ALWAYS WEAR SEATBELTS
Always keep head, arms & body parts within vehicle.
Fully secure or stow the soft top before driving according to instructions.
Never try to latch or fold soft top while driving. Do not use if damaged or
worn.
Read and follow all instructions & warnings accompanying this product, in
your vehicle owner's manual and Off Road Driving Supplement.
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 4
QTY 2
®
Wrangler JK
REQUIRED TOOLS:
SAFETY GLASSES
PHILLIPS SCREW DRIVER
FLAT HEAD SCREW DRIVER
T-30 TORX DRIVER
PLIERS
Advertisement
Related Manuals for Quadratec QuadraTop Adventure Top S With Flip Back Sunroof
Summary of Contents for Quadratec QuadraTop Adventure Top S With Flip Back Sunroof
- Page 1 Adventure Top S QuadraTop ® With Flip Back Sunroof for 2007-2018 ® 2 Door Jeep Wrangler JK Item 11113.1435 This Replacement Top kit is designed to fit on your 2 Dr Jeep® Wrangler when the original soft top or hard top has been completely removed. Before begin- NOTICE ning your installation of this product, you will need to remove your existing soft top fabric, hardware or Hard top.
- Page 2 Careful attention is required to this instruction or operation but does genera- NOTICE lly not relate to personal injury. Damage to your Quadratec® product or other property may result if you don’t follow instructions. Before you begin Installation:...
- Page 3 FIG 6 FIG 5 Secure the over door bow to the Header leg with the attached set screw (Fig 6).Slide the bow sleeve over the knuckles as shown in Fig 7. Fig 7 Repeat this procedure on the opposite side. Locate the bow mounting brackets over the fac- Step 2: Install Bow Mount Brackets to Roll Bar tory holes and using the Allen head pivot bracket...
- Page 4 FIG 14 FIG 15 Pillar and Over Door Surround Assembly to secure the top over door assembly with the Locate the driver’s side Rear over door assembly Pillar assembly. See FIGs 18 &19. and the driver’s side Pillar assembly shown in FIG16.
- Page 5 FIG 24 FIG 23 FIG 25 FIG 26 FIG 28 FIG 27 FIG 29 Install Door Surrounds to Jeep Locate the assembled Passenger side rear door surround (Fig23). On the bottom of the vertical pillar portion of the assembled door surround is a pin that will be inserted into the body tub (FIG 24).
- Page 6 FIG 34 FIG 33 FIG 35 FIG 36 FIG 38 FIG 37 FIG 39 FIG 40 hole (Fig 41) and attach the quick release knuc- Step 5: Installing the Header/Deck Fabric Fa- bric to the Center Bow kles to the center bow (Fig 42). Repeat on other With the help of a friend, locate the completed side of vehicle.
- Page 7 FIG 43 FIG 44 FIG 46 FIG 45 Attach the spring end to the webbing as shown in figs 46 and 47. FIG 47 Using pliers, crimp the spring end so it does not come loose. Do not tighten this strap yet. Note: FIG 47 Shows a D-ring attached to the strap/spring.
- Page 8 FIG 50 FIG 51 FIG 53 FIG 52 FIG 54 NOTE: Do not completely tighten these straps yet. They should be holding the top but not pulled as tight as possible. You will do final “tightening” after you install the windows. IMPORTANT: The top deck MUST be centered on the rear of the vehicle for the NOTICE windows to fit properly.
- Page 9 FIG 57 FIG 58 FIG 59 FIG 60 FIG 61 FIG 62 When removing the quarter and rear windows from the Top deck be sure to sli- de them out completely before pulling down. Disengage the side hook and loop NOTICE before sliding the windows out.
- Page 10 FIG 65 FIG 64 FIG 66 FIG 68 FIG 67 FIG 69 FIG 70 Step 9: Installing the Tailgate Bar and Rear into the mounts with the outside of the fabric Window to the body of the Jeep® facing towards the rear of the Vehicle (Figs 73 & 74).
- Page 11 FIG 73 FIG 74 Step 9B: Installing the Tailgate Bar and Rear Window to the body of the Jeep® Once the Tailgate bar is secure, lower zippers on both sides of the rear curtain (FIG 75) and then secure the rear zipper cover flap as shown in Figs 76 &...
- Page 12 “polished” out using window polish (Available prevent damage and keep the zippers in a at Quadratec.com). smooth working condition. If zipper opens behind the slider, the slider may have been Water/Fabric: In the event of seeping spread apart.
- Page 13 Quadratec, Inc. 1028 der shall, upon Quadratec inspection and Saunders Lane, West Chester, PA 19380. at Quadratec’s option, be either repair or replacement of product or parts (new or This Limited Warranty is the only warranty refurbished) covered under this Limited made in connection with purchase.