Advertisement
Quick Links
QuadraTop
This Replacement Top kit is designed to fit on your 4 Dr Jeep® Wrangler when
the original soft top or hard top has been completely removed. Before begin-
NOTICE
ning your installation of this product, you will need to remove your existing soft
top fabric, hardware or Hard top.
Loss of vehicle control involves risk of death or serious injury, particularly to
parts of your body not restrained within vehicle. This product is intended for
weather protection only and should not be relied upon to contain occupants
in the event of an accident or to protect from either ground contact or falling
objects. To reduce risk of accident or injury:
•
ALWAYS WEAR SEATBELTS
WARNING
•
Always keep head, arms & body parts within vehicle.
•
Fully secure or stow the soft top before driving according to instructions.
Never try to latch or fold soft top while driving. Do not use if damaged or
worn.
•
Read and follow all instructions & warnings accompanying this product, in
your vehicle owner's manual and Off Road Driving Supplement.
RISK OF EYE INJURY. Safety glasses should be worn at all times while install-
CAUTION
ing or maintaining this product.
PART LIST:
TOP DECK/HEADER AND REAR BOW ASSEMBLY QTY 1
DRIVER SIDE QUARTER WINDOW
PASSENGER SIDE QUARTER WINDOW
REAR WINDOW
CENTER BOW ASSEMBLY
DRIVER SIDE DOOR SURROUND
PASSENGER SIDE DOOR SURROUND
DOOR SURROUND KNOBS
TAILGATE BAR
TAILGATE BAR CORNER MOUNTS
TAILGATE BAR SHORT KNOBS
REAR BRACKET SCREWS WITH NUTS
BRACKET SCREWS
DOOR SURROUND BRACKETS
DOOR SURROUND RUBBER
4MM ALLEN WRENCH
Adventure Top
®
for 2018-2022
4 Door Jeep
Wrangler JLU
®
Item
11113.2335
#
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 1
QTY 8
QTY 1
QTY 2
QTY 2
QTY 4
QTY 8
QTY 4
QTY 2
QTY 1
REQUIRED TOOLS:
SAFETY GLASSES
SOCKET WRENCH
10MM SOCKET
Advertisement
Related Manuals for Quadratec QuadraTop 11113.2335
Summary of Contents for Quadratec QuadraTop 11113.2335
- Page 1 QuadraTop Adventure Top ® for 2018-2022 4 Door Jeep Wrangler JLU ® Item 11113.2335 This Replacement Top kit is designed to fit on your 4 Dr Jeep® Wrangler when the original soft top or hard top has been completely removed. Before begin- NOTICE ning your installation of this product, you will need to remove your existing soft top fabric, hardware or Hard top.
- Page 2 You CAN be moderately HURT and also may suffer property damage if you don’t follow instructions. Careful attention is required to this instruction or operation but does general- ly not relate to personal injury. Damage to your Quadratec® product or other NOTICE property may result if you don’t follow instructions.
- Page 3 Step 2: Rear Over Door Surround Line up the Driver’s side rear over- Assembly door assembly and the driver’s side Locate the driver’s side rear over door Pillar assembly, insert the screws into assembly, the rubber seal, the driver’s the two vertical holes and using the side Pillar assembly and the long Allen included 4mm Allen wrench, tighten head screws/ nuts (Fig 2).
- Page 4 Step 4: Install Rear Door Surrounds Insert this pin into the body tub as shown to Jeep Locate the assembled Driver’s in FIG’s 12 &13. Repeat this procedure side rear door surround (Fig 10). On on the passenger side rear door sur- the bottom of the vertical pillar portion round.
- Page 5 Step 5: Secure Front & Rear Door Slip the two knobs through the brackets Surrounds to the Roll Bar Continued holes in the rear door surround. Loose- ly tighten the knob securing the front Line up the rear end of the front door door surround.
- Page 6 Step 7: Installing the Rear Bow The rear bow mounts to the factory bracket behind the rear door surround The rear bow ships from the factory as shown in fig 23. Insert the screws bolted onto the Soft Top Deck/Head- and nuts, using a 10mm socket and er as shown in Fig 21.
- Page 7 Once lined up with the bow mount Step 8: Installing the top Deck and bracket, install the header assembly by Front Windshield channel Continued pulling out the quick release knob and Loosen the front bow mount brackets push over the mount until you hear a mounted on the door surround.
- Page 8 Step 9: Installing the top Deck Once the deck is secure on the side Continued brackets, With the help of a friend, SLOWLY fold the front header down Locate the driver side square bracket resting the windshield header on the on the rear driver door surround as cir- windshield.
- Page 9 Step 10: Installing the Side and FIG 41 Rear Windows Continued Once both quarter windows and the upper portion of the rear window are secured to the top deck, line up the driver’s side rear zipper on the Quarter window to the zipper on the rear window and zip it down a few inches (FIG 41).
- Page 10 Note: You may have to pull the Step 11: Securing the Side and Rear corners around towards the front or Windows to the Vehicle back of the vehicle to center the top on As shown in FIG’s 45 & 46, roll the the vehicle.
- Page 11 Step 13: Securing the tailgate bar & Once the Tailgate bar is secure, and rear window to the vehicle move to the rear driver’s side corner mounts and “roll” the plastic into the Take the tailgate bar and orient the corner mount as shown in FIG 57.
- Page 12 Using Your Fastback Soft Top Option #1 & #2 Your Soft top hardware has multiple Open over the front driver and pas- front fold back options. Depending senger compartments: on how much sun and weather you want to let into the cab determines the options available to you Unlatch the two front Windshield latch- es (Fig 60 &...
- Page 13 Using Your Fastback Soft Top Once The front bow arms and two Continued rear bows are disconnected from the bow mount brackets, with the help of Option #3 & #4 a friend, carefully fold back the front header and two bows layering the top Fully Open Front and Rear Passen- and bows under the fabric and then ger “Sun Roof”:...
- Page 14 (do not use “polished” out using the window polish listed the brush on the window glass!). You on page 15 (Available at Quadratec.com). can also use special soft top clean- ers Water/Fabric: In the event of seeping available on our website and shown on page 15.
- Page 15 Quadratec, Inc. 1028 der shall, upon Quadratec inspection and Saunders Lane, West Chester, PA 19380. at Quadratec’s option, be either repair or replacement of product or parts (new or This Limited Warranty is the only warranty refurbished) covered under this Limited Warranty.