Table of Contents
Advertisement
Available languages
Available languages
8.1.4.
Timer and clock settings
Unlock the screen:
- Press the button
for at least 3 sec. The buttons are unlocked and the symbol
automatically.
Clock setting:
- After power on, short press
- Short press
button to switch hour/minute setting, press the
- Press
button again to confirm the settings/changes and exit.
Timer setting:
1- After power on, long press
flash simultaneously;
2- Press the
and
buttons to set the exact hour(s).
3- Press
button to transfer to minute setting, minute icon ":88" flash, press the
4- Press the button
to confirm. In this moment, timer on icon
IMPORTANT: If step No4 is omitted, timer on icon
5- Press
button again to transfer to timer off setting, the "timer off" icon
6- Press the
and
buttons to change the hour(s).
7- Press button to transfer to minute setting, minute icon ":88" flash, press the
8- Press
button to confirm. In this moment, "timer off" icon
IMPORTANT: If step No8 is omitted, timer off icon
9- Press
button again to save and exit the timer setting interface.
IMPORTANT:
- If step No4 is omitted and all steps from 5 to 9 are done, "timer off" will be set and in stand by mode icon
- If step No8 is omitted, and all steps from 1 to 4 are done, "timer on" will be set and in stand by mode icon
- If all steps from 1 to 9 are done, both "timer on" and "timer off" will be set and icon
Timer canceling:
Do all steps from 1 to 9, without steps No4 and No8. The timer will be canceled
NOTE: 1)
The timer settings are automatically repeating.
NOTE: 2)
The timer settings are still valid after a sudden power cut.
8.1.5.
Setting button
1) Short press the button
•
AUTO mode. (Heat pump + E-heater will work according to the controller logic). The symbol
•
GREEN mode. (Only heat pump will work at normal working condition). The symbol
•
BOOST mode (Heat pump + E-heater will work at the same time). The symbol
•
E-HEATER mode. (Only E-heater will work). The symbol
•
VENTILATION mode. (Only fan will work). The symbol
2) Check the system parameters
•
In any status, press this button
•
Press the and
3) Adjust the system parameters. See 9.2. "Parameter list"
The parameters have been set; the user cannot change the parameters optionally. Please ask a qualified service
person to do this when required.
If no action is performed using the buttons for 10 seconds, the controller will exit and save the setting automat-
ically.
button to enter the clock setting interface, hour and minute icons "88:88" flash simultaneously.
button for 5 seconds to enter the timer setting interface, the timer on icon
1 1 1
2 2 2
and the working mode could be set.
and hold for 3 seconds, entry the system parameter checking interface.
buttons to check the system parameters.
and
buttons to set the exact hour(s) and minute(s);
1 1 1
ON
ON
ON
stops flashing that means "timer on" is set
2 2 2
1 1 1
will stay flashing and "timer on" is not set!
ON
ON
ON
2 2 2
1 1 1
and hour icon "88:" flash simultaneously.
2 2 2
OF
OFF F
OFF
1 1 1
stops flashing that means "timer off" is set
2 2 2
OFF F
OFF
OF
ON
ON
ON
will stay flashing and "timer off" is not set!
will appear on the display.
will appear on the display.
17
will appear. After 1 minute the buttons will lock
1 1 1
ON
ON
ON
2 2 2
OF
OFF F
OFF
and
buttons to set the exact minute(s).
and
buttons to change the minute(s).
1 1 1
2 2 2
OFF
OFF F
OF
1 1 1
2 2 2
1 1 1
will light on display.
ON
ON
ON
2 2 2
OFF F
OFF
OF
will appear on the display.
will appear on the display.
+
will appear on the display.
and hour icon "88:"
will light on display.
will light on display.
ON
ON
ON
Advertisement
Table of Contents
