Table of Contents
Advertisement
Available languages
Available languages
CAG/125-BL 20 V PLUS
off position when the power supply is inter-
rupted, e. g., in case of a power failure or
when the mains plug is pulled. This prevents
uncontrolled restarting.
Secure the workpiece. A workpiece clamped
f
with clamping devices or in a vice is held more
secure than by hand.
Do not open the battery. There is a risk of
f
short-circuiting.
Protect the battery against heat, e.g. against
f
continuous intense sunlight, fire, water, and
moisture. There is a risk of explosion.
In case of damage and improper use of the
f
battery, vapours may be emitted. Ensure the
area is well-ventilated and seek medical atten-
tion should you experience any adverse effects.
The apours may irritate the respiratory system.
Use the battery only in conjunction with
f
your FF GROUP Product. This is the only way in
which you can protect the battery against dan-
gerous overload.
The battery can be damaged by pointed ob-
f
jects such as nails or screwdrivers or by force
applied externally. An internal short circuit
may occur, causing the battery to burn, smoke,
explode or overheat.
PRODUCT SPECIFICATIONS
INTENDED USE
The power tool is intended for cutting, roughing
and brushing metal and stone materials without
the use of water. A special protective guard for
cutting must be used when cutting bonded abra-
sives. Sufficient dust extraction must be provid-
ed when cutting stone. With approved abrasive
tools, the power tool can be used for sanding with
sanding discs.
TECHNICAL DATA
Article number
Model
Rated voltage
No load speed
Max. grinding disc
diameter
Thread of grinder
spindle
Weight
Noise emissions
Sound pressure level
Sound power level
Uncertainty
Equivalent vibration levels
Max. vibration level
Uncertainty
47 874
CAG/125-BL 20V PLUS
V
20
min
8.500
-1
mm
125
M14
kg
1,80
dB(A)
83,7
dB(A)
94,7
dB (A)
3
m/s
1,547
2
m/s
1,5
2
IDENTIFICATION
1. Unlocking lever for protective guard
2. Direction of rotation arrow on housing
3. Spindle lock Button
4. On/Off switch
5. Handle (insulated gripping surface)
6. Protective guard for grinding)
7. Auxiliary handle (insulated gripping surface)
8. Clamping flange
9. Mounting flange
USE
MOUNTING OF ACCESSORIES (C, J, K)
Clean spindle and all parts to be mounted.
f
Tighten clamping flange (8) with spanner while
f
pushing spindle-lock button (3).
For removing accessories handle vice-versa.
f
MOUNTING OF AUXILIARY HANDLE (A, B)
Screw the auxiliary handle (7) on the right or left
of the machine head depending on the working
method.
REMOVING / MOUNTING / ADJUSTING OF PRO-
TECTIVE GUARD (G,H,I)
Open the guard by releasing the lever (1)
Place protective guard (6) on the spindle collar
f
and turn it to the required position (depending
on the work to be carried out).
Adjust protective guard (6) by pushing the lever
f
(1).
CHARGING THE BATTERY
Use only the chargers listed on the acces-
f
sories page of FF GROUP Power Tools cata-
logue. Only these chargers are matched to the
lithium-ion battery of your power tool
Note: The battery is supplied partially charged. To
ensure full battery capacity, fully charge the bat-
tery in the charger before using your power tool
for the first time. The lithium-ion battery can be
charged at any time without reducing its service
life. Interrupting the charging process does not
damage the battery.
Do not continue to press the On/Off switch
f
after the power tool has automatically
switched off. The battery can be damaged. Fol-
low the instructions on correct disposal.
REMOVING THE BATTERY (D, E, F)
To remove the battery, press the release button
and pull the battery forward and out of the power
tool. Do not use force to do this.
BEFORE USING THE TOOL
Ensure that accessory is correctly mounted and
f
firmly tightened.
Check if accessory runs freely by turning it by
f
hand.
Test-run tool for at least 60 seconds at highest no-
f
load speed in a safe position.
Stop immediately in case of considerable vibra-
f
tion or other defects and check tool to determine
the cause.
English | 13
www.ffgroup-tools.com
Advertisement
Table of Contents
