Safety Information And Introduction - EBARA FSA Instruction Manual

Safety Information and Introduction

Before handling this pump, always disconnect the power first. No open flame or use sparkable
electrical devices or flames in a septic (gaseous) or possible septic sump.
Do not work under heavy Suspended object unless there is a positive support under it to stop its fall in
event of sling or, hoist failure. Disregard of this warning could result in personal injury.
This pump should only be serviced by a qualified person or a factory trained person.
This instruction manual includes necessary items for installation, operation and maintenance.
Read this manual carefully to ensure correct installation, operation and maintenance.
Be sure to keep this instruction manual on hand for future reference.
Design of this EBARA pump is based on superior engineering and long experience. To prevent trouble and provide
satisfactory operation and long life, it is important to understand the EBARA pump thoroughly by careful study of this manual.
If any questions arise regarding this manual, please direct them to EBARA INDONESIA.
Specification
Be careful not to exceed the given specifications in the use of your products.
Check the following points upon receipt of your pump:
(1) The pump exactly what you ordered? Check the
nameplate. It is especially important that you check
whether the pump is to be used with 50 Hz.
(2) Has any damage occurred during shipment? Are any
bolts or nuts loose?
Description
Name
Liquid
Temperature
Max. Working Pressure
Synchronous Speed
Installation
Impeller
Shaft seal
Construction
Sealing
Bearing
Flange
Suction & Discharge
Casing
Impeller
Material Shaft
Seal
Bare shaft
Accessories
With motor
Note : Refer to the Standard Specification if you have purchased a standard model. We also offer pumps with optional features
according to customer demand.
Be careful not to exceed the given specification on the use of your pump.
WARNING
CAUTION
CAUTION
Standard
2 poles model
Clean water
o o
0 to 100 C (32 to 212 F)
2
10 bar (10.2 kgf/cm ) for standard flange JIS 10K RF
2
16 bar (16.3 kgf/cm ) for standard flange JIS 16K RF
-1
3000 min 1500 min
Indoors
Enclosed
Mechanical seal
Self flushing
Sealed ball bearing
Suction < φ 150 mm, except 100x65 FSKA
100x65 FSKA
Suction = φ 150 mm, except below models
150x100 FSKA; 150x100 FSNA
Suction = φ 200 mm, except below models
200x150 FSLA; 200x150 FSNA
Suction = φ 250
Cast Iron
Bronze Casting (CAC406/BC6)
403 Stainless steel
Mechanical Seal: Ceramic/Carbon/NBR
Common base, Coupling, Coupling guard
(3) Have all necessary accessories been supplied? (For
a list of standard accessories see Construction.)
We recommend that you keep a spare pump on hand in
case of emergencies. Keep this instruction manual in a
safe place for future reference.
4 poles model
-1
: JIS 10K RF
: JIS 16K RF
: JIS 10K RF
: JIS 16K RF
: JIS 10K RF
: JIS 16K RF
: JIS 16K RF
2
(Kg/cm =98,6 kPa)
- 1 -
Optional
2 poles model 4 poles model
2
16 bar (16.3 kgf/cm )
Outdoors
Gland Packing
External flushing
Oil bath (some models only)
16 bar : JIS 16K RF; DIN PN-16
DIN PN-16
16 bar : JIS 16K RF; DIN PN-16
DIN PN-16
16 bar : JIS 16K RF; DIN PN-16
DIN PN-16
DIN PN-16
Ductile Cast Iron (FCD)
Cast iron; Ductile Cast Iron (FCD)
304; 316 Stainless steel
Gland Packing : Teflon (PTFE) impregnated
Mechanical Seal : SiC/SiC
Priming funnel ; valve; Companion Flange
Priming funnel ; valve; Companion Flange