Register Unit Telephone Number; Select Line Type; Off-Hook Alarm; Change Defaults - Canon 5119B001AA Basic Operation Manual

Register Unit Telephone Number

Register your machine's fax number.
How to access the option
[ ] (Menu) → <Fax Settings> → <Basic Settings> →
<Register Unit Telephone Number>
How to register the fax number
Enter up to 20 digits using the numeric keys.
You can also enter the [+].

Select Line Type

Change this option when you cannot send a fax.
Contact your local telephone company when you are not
sure of the line type that you are using.
How to access the option
[ ] (Menu) → <Fax Settings> → <Basic Settings> →
<Select Line Type>
Settings
(Bold: Default setting)
Pulse Select this setting when you are using a pulse line.
Tone Select this setting when you are using a tone line.

Off-Hook Alarm

Specify whether to sound an alarm when the telephone
handset is left unhooked and adjust the volume.
How to access the option
[ ] (Menu) → <Fax Settings> → <Basic Settings> →
<Off-Hook Alarm>
Settings
(Bold: Default setting)
Off
Off-Hook Alarm Volume:
On
1 to 3

Change Defaults

Change the default settings, which become effective
when the machine is turned ON and OFF or [
pressed.
How to access the option
[ ] (Menu)→ <Fax Settings> → <TX Function
Settings> → <Change Defaults>
Settings
See the following section for more information.
"Changing the Default Fax Settings" (→P.6-22)

Register Unit Name (Fax)

Register your name or company's name (sender's name).
Once the information has been registered, it is printed at
the top of each page that you are sending.
How to access the option
[ ] (Menu) → <Fax Settings> → <TX Function
Settings> → <Register Unit Name (Fax)>
How to register the sender's name
Enter up to 24 alphanumeric characters.
"Entering Text" (→P.1-11)
6-24
No alarm sounds.
The alarm sounds at the
specified volume.
] (Reset) is
NOTE
Where the sender's name appears on the page
The information is printed at the top of each page that you are
sending.
Fax/Telephone Number
(FAX No.)
Sender Name
Sending Date/Time (Unit Name)
01/01/2011 02:07 PM FAX 123XXXXXXX
Telephone Number
Mark

ECM TX

The ECM (Error Correction Mode) detects and corrects
errors that occur during fax transmissions. It helps in
minimizing sending errors caused by a poor connection.
NOTE
Check if the ECM is enabled on the receiving fax
machine
The ECM is effective only when it is enabled on both machines.
An error occurs even when the ECM is enabled
The error may be caused by poor telephone line conditions.
When telephone line conditions are poor
It may take additional time to send your fax if a problem occurs
when sending over the telephone line.
How to access the option
[ ] (Menu) → <Fax Settings> → <TX Function
Settings> → <ECM TX>
Settings
(Bold: Default setting)
Off Disable the ECM.
On
Enable the ECM.

Pause Time

Press [ ] (Pause) to specify the pause length.
For the instructions on how to enter a pause, see "Sending a
Fax Abroad (Adding Pauses)" (→P.6-10).
How to access the option
[ ] (Menu) → <Fax Settings> → <TX Function
Settings> → <Pause Time>
Setting
(Bold: Default setting)
1 to 2 to 15
(seconds)

Auto Redial

Enable auto redial for automatically redialing the fax
number when the line is busy or a sending error occurs.
Specify the number of redial attempts and the interval
between these attempts.
How to access the option
[ ] (Menu) → <Fax Settings> → <TX Function
Settings> → <Auto Redial>
Page Number
CANON 0001/0001