Related Manuals for BWT PERMAQ COMPACT 41
Summary of Contents for BWT PERMAQ COMPACT 41
- Page 1 Installation and Operating manual ® BWT PERMAQ COMPACT 41 Reverse Osmosis Plant www.bwt-group.com...
-
Page 3: Table Of Contents
13.3 Wiring diagram ......................21 13.4 PCB ..........................22 13.5 Start-up test ........................23 13.6 Operating journal ......................24 Spare-parts list BWT PERMAQ ® Compact 41 ..............25 13.7 13.8 Spare-parts drawing ....................... 26 13.9 Declaration of Conformity ....................27... -
Page 4: General Information
BWT service technician. have been 7. The warranty becomes inva- moved from the The outside measures of the BWT lid, if maintenance intervals raw water. ® PERMAQ Compact 41 plant are are not met. Raw water... -
Page 5: Water Quality
The hose may servicing of the plant. Ensure that not be led down into the outlet BWT keeps a complete assembly the plant can easily be pulled out water, though, since the water ®... -
Page 6: Adjustment Of Concentrate Amount
The plant must operate and capacity the pressure shown on flush to drain for 20-30 the manometer must be approx. minutes before readjusting the Ex.: BWT PERMAQ ® Compact 41 14,5 to 16 bar PI1. (Section concentrate/recirculation with 40 % recovery: 10.2, Fig. -
Page 7: Setting Permeate Outlet Pressure
FUNCTIONS slowly shutting off the raw-water supply while the RO plant is still ® operating. When the water sup- The BWT PERMAQ Compact 41 ply has been interrupted, the RO plant comes with a control box plant should stop automatically with following built-in functions: ... -
Page 8: Maintenance And Trouble-Shooting
MAINTENANCE AND TROUBLE-SHOOTING Maintenance ® The BWT PERMAQ Compact 41 plant is produced and designed for a minimum of servicing and maintenance. However, there are certain functions which should be checked regularly. Maintenance intervals should be per- formed once a week – read section 13.5 Operating Journal. -
Page 9: Trouble-Shooting
Trouble-Shooting This section deals with the problems that may arise on the plant. 9.2.1 The plant capacity has dropped... -
Page 10: The Quality Of The Treated Water Is Higher Than 50 Μs/Cm
9.2.2 The quality of the treated water is higher than 50 μS/cm 9.2.3 Alarm: Low water pressure... -
Page 11: Alarm: Pump
9.2.4 Alarm: Pump 9.2.5 The plant is not operating... -
Page 12: Alarm: The Pump Starts And Stops
9.2.6 Alarm: The pump starts and stops 9.2.7 Hard water is measured at soft-water tap (option) -
Page 13: Overview Of The Alarm Conditions
Overview of the alarm conditions LED function: In normal operation the LED’s are lit corresponding to the components they represent. External stop: Remove the cause to ex- (Nothing is working) ternal stop signal Automatic restart Too low inlet pressure: (3 times) if raw water (Pump stopped) pressure is <0.5 bar ALARM - Too low raw water... -
Page 14: Settings
Selection of BWT PERMAQ ® Compact 41 model No. 4-8 Flush time (The seconds added together gives the flush time) 10 TECHNICAL SPECIFICATIONS 10.1 Technical data BWT PERMAQ ® Compact 41 Units Values Capacity * Maximum water recovery 40-75 Hydrophore 11 / 3.5... -
Page 15: Technical Specifications
10.2 Technical specifications Signature Designation Type/data High-pressure pump 1x230V, 0.64kW Manometer 0-25 bar, ¼” Manometer 0-6 bar, ¼” PS 1 Pressure switch NO ¼”, 0.5 bar PS 2 Pressure switch NC ¼”, 5.2 bar Needle valve (Recirculation) Brass Needle valve (Concentrate) Brass Needle valve (Permeate) Brass... -
Page 16: Functional Description
11 FUNCTIONAL ble connections. The plant can be it goes, the pipe can be pulled placed under a standard table and out. DESCRIPTION simply pulled out for servicing. Dismount the lock placed at the end of the membrane The raw water that is led to the Under normal operating conditions pipe. - Page 17 11. Dismount the permeate hose normal operating pressure. and lead it to drain. 16. Check that the water quality is 12. Reconnect power to the plant. < 50 μS/cm. 13. The plant will now be operat- Write in the operating journal: ing.
-
Page 18: Various Enclosures
13 VARIOUS ENCLOSURES 13.1 P&I diagram 13.2 Layout drawing 13.3 Wiring diagram 13.4 PCB 13.5 Start-up test 13.6 Operating journal 13.7 Spare-parts list BWT PERMAQ ® Compact 41 13.8 Spare-parts drawing 13.9 Declaration of conformity... -
Page 19: P&I Diagram
13.1 P&I diagram... -
Page 20: Layout Drawings
13.2 Layout drawings... -
Page 21: Wiring Diagram
13.3 Wiring diagram... -
Page 22: Pcb
13.4 PCB... -
Page 23: Start-Up Test
NO, the problem does not concerns the plant or the installation The plant - we mean only the part of the whole installation which was delivered by BWT (i.e only the plant). The installation - we mean the piping etc. leading to the plant. -
Page 24: Operating Journal
13.6 Operating journal Maintenance intervals should be performed once a week. Replacement frequency of wearing parts shown in ® section 13.6 Spare Parts List BWT PERMAQ Compact 41. -
Page 25: Spare-Parts List Bwt Permaq ® Compact 41
3 years 16 µF capacitor (High pressure motor) 750001860 Options Assembly kit for water supply 656525100 Filter housing 10" complete 321401000 Filter wrench 321417100 Carbon filter 10" 321413000 ½ year Softening plant * Contact your local BWT dealer for detailed information. -
Page 26: Spare-Parts Drawing
13.8 Spare-parts drawing... -
Page 27: Declaration Of Conformity
EC Declaration of Conformity for Machinery Directive 2006/42/EC, Annex II, A Low Voltage Directive EMC Directive BWT HOH A/S Geminivej 24 - DK-2670 Greve tel.: +45 43 600 500 - fax: +45 43 600 900 bwt@bwt.dk - www.bwt.dk herewith declares that: ®... - Page 28 Fax: +33 1 4922 45 45 E-Mail: office@bwt.at E-Mail: bwt@bwt.de E-Mail: info@cillichemie.com E-Mail: bwt@bwt.fr BWT Belgium NM. BWE Česká Republika s.r.o. BWT Polska Sp. z o.o. BWT Hungária Kft. Leuvensesteenweg 633 Lipovo 196 -Cestlice ul. Polczyhska 116 Keleti út. 7. B-1930 Zaventem CZ-251 01 Říčany...
Need help?
Do you have a question about the PERMAQ COMPACT 41 and is the answer not in the manual?
Questions and answers