Content 1 General information .............. 5 2 Explanation of words ............5 3 Function descriptions ............. 6 Permeate production ....................6 4 Positioning of the RO unit ............6 5 Water quality ................ 7 6 Water connections ..............7 Connection of feed water (inlet water) ................7 Connection of outlet hose ....................
Page 4
Overview of the Status- and Alarm LED ..............19 11.4 Troubleshooting ....................19 12 Technical specifications ............20 13 Appendix ................21 13.1 Preset standard values for BWT bestaqua 60, 61 and 62 ........21 13.2 Wiring diagram ....................22 13.3 PI-diagram ......................25 13.4 Arrangement drawing ...................
General information Your BWT bestaqua 60-62 is of a compact design with integrated reservoir tank in order This installation and operating manual (OPM) to take up as little space as possible. applies bestaqua 60-62 total With its compact and finished design, your desalination unit.
Level switch: Is a switch, which gives a water in the reservoir does not overflow when signal when the BWT bestaqua 60-62 unit the tank is full. must either be started or stopped, and it stops...
The best operating result is obtained by The feed water, which is to be treated in the connecting to minimum ¾” feed-water pipe. BWT bestaqua 60-62 unit, must be drinking That reduces the drop in pressure to the RO water quality with maximum 500 mg/l TDS.
Note! The electrical connections must be made in compliance with local regulations. Install the supplied 12 mm plastic hose to outlet. The electrical connection to the BWT bestaqua 60-62 unit must be as follows: Note! It is important that the hose is pressed ...
Function buttons og display elements [ON/OFF] key switches the device from standby to ON/OFF when pressed continuously for 2 sec and performs the reset of the device in case of alarms and/or failures. [ON/OFF] key stop/pauses the RO unit when pressed shortly (Arrow up) key scrolls through the menu pages upward / right, increases the value of the parameter presently shown on the display.
Start-up of the RO unit Note! Only for BWT bestaqua 60 LT: After 30 minutes’ rinse the RO unit will Read section below carefully before starting automatically start to produce permeate if up the RO unit. there is consumption. But the technician can use flowmeter from 451409006 “RO...
permeate capacity bestaqua 60-62 at a temp. of 10-25 °C. If the temp. is below 10 °C, the capacity will Outlet amount (l/h) be 3 % below normal capacity for every degree under 10 °C. If e.g. the feed-water temp. is 8 °C, for an...
10 Automatic functions the lock nut. NB! When the valves have been locked, the The BWT bestaqua 60-62 unit is equipped RO unit shall be started and stopped 4-5 times with a control box which has following built-in and then the flow shall be checked again; the control functions: valves are re-adjusted if necessary.
V-cup seal must be fitted at the same end of the membrane as the old one, i.e. if the V- The BWT bestaqua 60-62 unit is produced cup seal is at the top of the pressure vessel., and designed for a minimum of servicing and the V-cup seal of the new membrane must also maintenance.
Please observe: If your reverse osmosis is not performing as it should, please run through the alarm messages below. In the case of a fault, repair work may only be carried out by an expert (call BWT SERVICE technician). When Alarm sound press on to see Alarm details.
13 Appendix 13.1 Preset standard values for BWT bestaqua 60, 61 and 62 Parameter: Interval and unit: Default values: DATE [Day /month / year] Actual date TIME [Timer : minutter] Actual time LANGUAGE EN, DK, DE, IT, FR CONDUCTIVITY LIMIT 0-190 µS...
13.6 Operating journal Maintenance intervals should be performed once a week. Replacement frequency of wearing parts shown in chapter “14.8 Spare parts list BWT bestaqua 60-62”.
13.8 Spare part list Position BWT bestaqua 60, 61 and 62 Spare part No. Recommended Recommended spare parts replacement frequency High-pressure motor 451202495 High-pressure pump 451202490 Coupling for HP pump 451202485 Transport pump 454100070 Check valve ½" 200729004 Pressure tank...
Member States requires electrical and electronic equipment to be collected separately from unsorted municipal waste so that it may be recycled. In Denmark and several other countries, BWT itself assumes responsibility for the return and conformant disposal of its electronic and electrical products. These products may not be placed with household waste or brought to collection centres run by local public disposal operations –...
+45 43 600 500 - fax: +45 43 600 900 bwt@bwt.dk - www.bwt.dk herewith declares that: BWT bestaqua 60LT, 60HQ, 61LT, 61HQ, 62LT, 62HQ is in conformity with the provisions of the Machinery Directive (directive 2006/42/EC) is in conformity with the provisions of the following other EC directives...
Page 36
Fax: +33 1 4922 45 45 E-Mail: office@bwt.at E-Mail: bwt@bwt.de E-Mail: info@cillichemie.com E-Mail: bwt@bwt.fr BWT Belgium NM. BWE Česká Republika s.r.o. BWT Polska Sp. z o.o. BWT Hungária Kft. Leuvensesteenweg 633 Lipovo 196 -Cestlice ul. Polczyhska 116 Keleti út. 7. B-1930 Zaventem CZ-251 01 Říčany...