LIST OF CONTENTS GENERAL EXPLANATION OF WORDS PLACING OF PLANT WATER QUALITY WATER CONNECTIONS ELECTRICAL CONNECTIONS START-UP OF PLANT 7.1 Adjustment of outlet amount 7.2 Adjustment of the Recirculation Amount OPERATING MANUAL FOR OPERATOR MENU 8.1.1 Information in menu: 8.1.2 Functions in menu: 8.2 Operation 8.2.1...
Page 4
13. VARIOUS ENCLOSURES 13.1 P & I Diagram 13.2 Layout Drawing 13.3 Operating journal 13.4 List of components and Spare parts for the BWT PERMAQ® PRO 2500 series 19 13.5 Spare parts drawing 13.6 Declaration of Conformity 13.7 Circuit diagram...
GENERAL have to be refitted. quality. This user guide applies to the BWT PERMAQ® PRO 2500 The BWT PERMAQ® PRO 2500 Membranes Is the plant filter series of total desalination plants. plant is designed for minimum which by high...
1" flexible pressure hoses. KMnO max.: 10 mg/l possibly a reservoir tank (option). BWT sell complete assembly kits Maximum temperature:25 C. for the BWT PERMAQ® PRO You must expect 1000 mm extra Note! The plant has been 2500- series.
Permeate Drainage The electrical connection to the Plant capacity amount l/h BWT PERMAQ® PRO 2500 Completely open the outlet valve type plant must be as follows: V4. (See diagram of principle). 75 % Completely close the recirculation 2500...
Press Alarm setting the stated intervals In case of deviations you may contact In alarm setting you can make BWT’s service department. selections for set point and delay of alarms. if the capacity has...
8.2.2 Functions in Opr. Setting 2 Operating status of valves and Operation: pumps. Press OFF-ON RO: Pumps change colour (black = stopped, white = operating) For start/stop of plant. Valves change colour (black = Press OFF-ON FLUSH: closed, white = open.) For start/stop flush of plant.
ENT. for scrolling up and down in the alarm display. 8.10.3 Password: Password will be informed if you Date/time contact BWT A/S Tel.: +45 43600500 Service Department 8.7.1 Information in Plant MAINTENANCE type: AND TROUBLE- RO Type and selection of option.
following must be checked 9.2.1 The plant capacity 12. Replace defective/buzzing regularly: has decreased switches and relays If the operating conditions of the This can be read on the flow Note! If the plant has to be plant are changed compared to meter (FI1) while the RO plant is taken out of operation for a long the settings on the day of start-up,...
Write down in the day. After rinsing the outlet REPLACEMENT operating journal: amount must be readjusted, see OF MEMBRANES paragraph for Start-up of the Read this paragraph before 13. Date of replacement of Plant. membranes. dismounting/replacing the plant membranes. 14. New capacity of the plant Check: (flow meter FI1 and FI2) if raw water comes in connection...
10. 21. Lift the dosing control until increased pressure loss across the BWT CIP 4 is sold by BWT Item the control signal disappears, membrane and thus a drop in and then lower it just enough No.: 70 19 57 020...
Page 14
CIP pump P2 by pressing "stop" “Start-up of plant”. on the panel front. Start by cleaning with BWT CIP Let the membranes soak for about 10 and then clean with BWT CIP 4. Always follow the safety 1 hour.
VARIOUS ENCLOSURES 13.1 P & I diagram 13.2 Lay-out drawing 13.3 Operating journal 13.4 List of components and spare parts for RO 13.5 Spare parts drawing 13.6 Declaration of Conformity 13.7 Circuit diagram...
13.4 List of components and Spare parts for the BWT PERMAQ® PRO 2500 series Recommended Recommended Item No. Item text – RO plant Item No. replacement spare parts frequency (month) ¾” Needle valve with counter nuts 200731006 1” Ball valve 200742008 ¼”...
Page 20
14 mm collector 454097014 48-60 14 mm elbow 454090014 48-60 14 mm T-piece 454095014 48-60 4” end plate 451404113 48-60 4” end plate 451404112 48-60 Lip ring for 4” membrane 6-12 451404208 48-60 * Contact your local BWT dealer for detailed information.
+45 43 600 500 - fax: +45 43 600 900 bwt@bwt.dk - www.bwt.dk Herewith declares that: BWT PERMAQ® Pro 2510, 2520, 2530, 2540 is in conformity with the provisions of the Machinery Directive (Directive 2006/42/EC) is in conformity with the provisions of the following other EC directives...
Need help?
Do you have a question about the PERMAQ PRO 2500 Series and is the answer not in the manual?
Questions and answers